Bedec Extra Flex Elastomeric Masonry Paint

Non Hazardous
Microporous Masonry Paint with up to 400% elasticity for use over cracks. For roughcast, pebble-dash, brickwork, cement and concrete rendered surfaces.
Available in 5 Litres
From £51.90 £43.25
In stock
Only %1 left
Product Description

Bedec Extra-Flex Masonry Paint, for rough-cast, pebble dash, brickwork, cement and concrete rendered surfaces, providing a smooth, long-lasting finish that stretches up to 400% to prevent further cracking.

Bedec Extra-Flex Masonry Paint is an ideal purchase for anyone looking to protect exterior masonry, such as roughcast, pebble-dash, brickwork, cement and concrete rendered surfaces. The modified acrylic blend is a flexible microporous protective coating that will flex with the substrate where movement causes cracking in conventional coatings. It can be applied to previously painted surfaces after suitable preparation and can be used as an anti carbonation coating to help prevent concrete spalling.

Best Uses

Extra-Flex is best used to bridge hairline cracks found in exterior walls. It is ideally suited for the protection of exterior masonry, roughcast, pebble-dash, brickwork, cement and concrete rendered surfaces. This paint provides surfaces with a smooth, long-lasting finish that stretches up to 400%, to aid the prevention of further cracking after the fine cracks have been bridged.

  • Smooth finish masonry paint
  • Long-lasting coating
  • Microporous
  • Flexible - prevents cracking
  • Fine crack bridging
  • Stretches up to 400%
  • Available to mix in pastel colours
  • Most colours available by special order.


Bedec Extra-Flex Masonry Paint is suitable for application by brush, roller, airless spray, conventional spray or HVLP equipment. It should not be applied at temperatures below 10°C or if rain is expected before the paint is touch dry. The paint has a theoretical coverage rate of 10m2 per litre depending on the surface and is touch dry in just 2 hours at 20°C, where relative humidity (RH) should not exceed 65%. At this temperature, a second coat can be applied after 4 hours, although this time will need to be increased at lower temperatures. If in doubt, allow extra time for the paint to dry.

Extra-Flex is not recommended for application to Fletton or Stock Bricks or to walls that have been coated with Limewash. We can talk to you about a different coating if you need to coat one of the previously mentioned substrates. Our guide to painting exterior brickwork offers advice that will help you here.

Surface and Environment

Bedec Extra-Flex is a masonry paint. It can be used on a wide range of exterior masonry surfaces and works well in the outdoor environment to protect surfaces against further damages caused by weathering. It can be applied to a range of walls and is available in almost every colour when you contact our technical support team.

Technical Details
Components: One Part
Type: Water-based Acrylic
Finish: Smooth Satin
Stock Colours: Range of Stock Colours
Tintable: Upon Special Request, Depending on Quantity. Please note, bespoke tints are non-refundable / exchangeable.
VOC Content: 140.0g per Litre
Volume Solids: 48%
Suitable Substrates: Exterior Masonry, Roughcast, Pebble-dash, Brickwork, Cement and Concrete Rendered Surfaces
Application Method: Brush, Roller, Conventional H.V.L.P or Airless Spray
Theoretical Coverage: 9 -11 m2 per litre per coat
Wet Film Thickness (WFT): 100 microns
Dry Film Thickness (DFT): 42 microns
Induction Time: -
Pot Life: -
Touch Dry: 2 - 4 hours at 18°C
Overcoatable: 4 hours at 18°C
Fully Cured: 16 - 24 hours at 18°C
Cleaner / Thinner: Clean up with warm soapy water
Shelf Life: 24 months
Packaging: Available in 5 Litres
Product Video

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Related Products