Hempel Hempadur Multi-Strength 45753

SKU
id21237
Part A: UN1263 (Class: 3, Pk Grp: III), Part B: UN3469 (Class: 3.8, Pk Grp: III)
A self-priming, two-component, high build, pure epoxy paint which cures to an abrasion and corrosion resistant coating.
Available in 20 Litres in 12340 Grey or 50630 Red
From £222.32 £185.27
In stock
Only %1 left
Product Description

Hempel Hempadur Multi-Strength 45753 is a self-priming, two-component, high build, pure epoxy paint which cures to an abrasion and corrosion resistant coating. Applicable by standard heavy duty airless spray equipment.

Best Uses

Hempel Hempadur Multi-Strength 45753 is formulated as a heavy duty coating for areas exposed to abrasion and aggressive corrosive climate such as ramps, ship hulls and holds of bulk carriers. Hempel Hempadur Multi-Strength 45753 is also suitable as a ballast tank coating for special purposes such as chemical carriers carrying hot cargoes and other purposes where “pure epoxy coating” is requested.

Hempel Hempadur Multi-Strength 45753 can be used as a finishing coat where a cosmetic appearance is of less importance. HEMPADUR MULTI-STRENGTH 45753 is intended for use in cold climates.

Application

New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Abrasive blasting to minimum Sa 2½ (ISO 8501-1: 2007) with a surface profile corresponding to Rugotest No. 3, N9a to N10, preferably BN9a to BN10, Keane-Tator Comparator, 2.0 G/S or ISO Comparator, Medium (G).

Repair and Maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Remove all rust and loose material by abrasive blasting or power tool cleaning. Feather edges to sound and intact areas. After wet abrasive blasting hose down the surface with fresh water and allow drying. Touch up bare spots with: specified Hempel Hempadur paint

Use only where application and curing can proceed at temperatures between: -10°C/14°F - 20°C/68°F. The temperature of the paint itself should be above: 15°C/59°F. Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation. In confined spaces provide adequate ventilation during application and drying. Curing requires a relative humidity of: max. 85%.

Technical Details

Approvals

  • Hempadur Multi-Strength 45753 tested by Teknologisk Institut AS, Norway, and approved for internal use in pipe lines for water power generation according to NS 5417
  • Recognized Abrasion Resistant Ice Coating by Lloyds Register
  • Complies with EU Directive 2004/42/EC: subcategory j
  • NORSOK System 7A approved.

Technical Info

Components: Two Pack
Type: Epoxy Paint
Finish: Semi Gloss
Stock Colours: 12340 Grey and 50630 Red
Tintable: Yes, upon request. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 233 g/L
Volume Solids: 79%
Suitable Substrates: For marine ramps, ship hulls, ballast tanks or as a finishing coat where cosmetics are not important
Application Method: Airless Spray
Theoretical Coverage: 4 m2 per litre at 200 microns
Wet Film Thickness (WFT): 250 microns
Dry Film Thickness (DFT): 200 microns
Induction Time: -
Pot Life: 1 hour at 20°C
Surface Dry: 2 hours at 20°C
Overcoatable: See data sheet
Fully Cured: 14 days at 20°C
Cleaner / Thinner: Thinner: Hempel Thinner 08450 (5%), Clean tools with Hempel Tool Cleaner 99610
Shelf Life: See container
Packaging: Available in 20 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Related Products