Interline 955 is primarily intended for the internal lining of chemical storage tanks and vessels where acidic chemicals or hot media are to be stored, such as in oil, gas and chemical processing, pulp and paper plants, and for structural steelwork in environments where frequent contact with corrosive chemicals is likely to occur.
All surfaces to be coated should be clean, dry and free from contamination. Prior to paint application all surfaces should be assessed and treated in accordance with ISO 8504:2000. Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning.
Abrasive blast clean to Sa2½ (ISO 8501-1:2007) or SSPC-SP10. If oxidation has occurred between blasting and application of Interline 955, the surface should be reblasted to the specified visual standard. Surface defects revealed by the blast cleaning process should be ground, filled, or treated in the appropriate manner. A sharp, angular surface profile of 75-100 microns (3-4 mils) is recommended.
If a holding primer is required for Interline 955 then the use of Interline 949 is advised (see system compatibility). Alternatively, the blast standard can be maintained by the use of dehumidification.
Shop Primed Steel
Prior to application of Interline 955, all shop primed steelwork must be re-blasted to a visual standard as outlined above.
Concrete should be well cured prior to application of the flooring, lining or coating system. Refer to the Concrete Surface Preparation Guidelines for more information.
Material is supplied in two containers as a unit. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified. Agitate Base (Part A) with a power agitator. Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator.
Interline 955 should be applied to correctly prepared substrates. However, it is suitable for application to the following primers:
Interline 955 should only be overcoated with itself.
|Type:||Glass Flaked Reinforced Vinyl Ester|
|Stock Colours:||White, Buff|
|VOC Content:||29 g/L|
|Suitable Substrates:||For the internal lining of chemical storage tanks and vessels where acidic chemicals or hot media are to be stored, such as in oil, gas and chemical processing, pulp and paper plants, and for structural steelwork in environments where frequent contact with corrosive chemicals is likely to occur..|
|Application Method:||Airless Spray, Brush|
|Wet Film Thickness (WFT):||471 - 706 microns|
|Dry Film Thickness (DFT):||400 - 600 microns|
|Pot Life:||1 hour at 15°C|
|Touch Dry:||4 hours at 15°C|
|Overcoatable:||Between 5 hours to 3 days at 15°C|
|Hard Dry:||5 hours at 15°C|
|Cleaner / Thinner:||Do not thin|
|Shelf Life:||6 months minimum at <20°C (68°F). Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.
During storage and shipment, Interline 955 initiator must not be exposed to temperatures exceeding 30°C ( 90°F). Refrigeration recommended. Best practice would be to hold Parts A and B in separate stores
|Packaging:||Available in 20 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.
A high performance masking tape for professional use.