Jotun Penguard Express

SKU
id17015
Parts A and B: UN1263 (Class: 3, Pk Grp: III)
A two component fast drying coating. Can be applied on steel, aluminium and concrete at sub zero surface temperatures.
Available in 5 and 20 Litres
From £63.89 £53.24
In stock
Only %1 left
Product Description

Jotun Penguard Express is a two component, fast drying, protective epoxy coating for steel, aluminium and concrete substrates which are exposed to atmospheric corrosion.

This product is part of the Network Rail/Railtrack RT98 System M20

Jotun Penguard Express is a fast drying, high solids, high build product. Being a two component amine cured epoxy coating, it is designed for new construction where a fast drying product is essential. Penguard Express can be used as a primer, mid or finish coat and can be used as a single coat system in atmospheric environments.

Jotun Penguard Express is suitable for suitably prepared carbon steel, aluminium, concrete and galvanised steel substrates. It can be applied in sub zero temperatures.

Best Uses

Jotun Penguard Express is suitable for use on structural steel and piping which is exposed to environments with high levels of corrosive destruction. It is recommended for offshore environments refineries, power plants, bridges, buildings and mining equipment.

Can be used as primer, mid coat, finish coat or as single coat system in atmospheric environments. Suitable for properly prepared carbon steel, aluminium, concrete and galvanised steel substrates. It can be applied at sub zero surface temperatures.

Application

Recommended application is with an airless spray. A brush can be used for stripe coating and small areas. Follow application guide download for instructions.

Surfaces and Environment

Jotun Penguard Express is suitable for structural steel and piping which is exposed in environments which has high levels of atmospheric corrosion.

Technical Details

Approvals

  • This product is part of the Network Rail/Railtrack RT98 Systems M20 and N1
  • Certificate numbers XM92/M20-140, M20-179, XN90/N1-075 and N4-102
  • Pre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1, suitable for exterior exposure in offshore environment, below 120 °C Tested in accordance with ISO 12944-5, C5-High environment
  • Low Flame Spread in accordance with EU Directive for Marine Equipment. Approved in accordance with parts 5 and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with IMO 2010 FTP Code Ch. 8

Technical Info

Components: Two Part
Type: Amine cured epoxy coating
Finish: Matt
Stock Colours: Grey, Grey XO, Red, Buff, Light Red
Tintable: No
VOC Content: 264.0g per litre
Volume Solids: 74%
Suitable Substrates: Suitable for properly prepared carbon steel, aluminium, concrete and galvanised steel substrates
Application Method: Airless Spray, Brush
Theoretical Coverage: 9.9 - 3m2 per litre
Wet Film Thickness (WFT): 100 - 340 microns
Dry Film Thickness (DFT): 75 - 250 microns
Induction Time: -
Pot Life: 2 hours at 23°C
Touch Dry: 15 hours at 10°C
Overcoatable: 30 hours at 10°C
Fully Cured: 15 days at 10°C
Cleaner / Thinner: Jotun Thinner No. 17
Shelf Life: 12 months
Packaging: Available in 5 and 20 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use