Jotun Penguard Pro

SKU
id17165
Part A and B: UN1263 (Class: 3, Pk Grp: III)
Specially designed as a universal, all round, new construction coating. Can be used as primer, mid coat, finish coat or as single coat system.
Available in 20 Litres
From £263.24 £219.37
In stock
Only %1 left
Product Description

Jotun Penguard Pro is a two component amine cured epoxy coating that is a surface tolerant, high solids, high build product. Specially designed as a universal, all round, new construction coating. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments.

Best Uses

Jotun Penguard Pro is suitable for properly prepared carbon steel, stainless steel, aluminium, galvanised steel and thermally sprayed zinc substrates. Suitable for structural steel and piping to be exposed to corrosive environments up to very high and immersed. Recommended for offshore environments, including splash zones, refineries, power plants, bridges, buildings and mining equipment. Specially designed as a universal product in coating systems where extended durability is required. The product provides great flexibility in choice of dry film thickness range as well as area of use.

Application

Prepare carbon steel to Sa 2½. Prepare stainless steel to cleanliness and surface profile corresponding to Sa 2½. Prepare aluminium to Sa 1. For galavanised steel, prepare by light brush blasting using non metallic abrasive leabing a clean, rough and even pattern. For shop primed steel, abrasive sweep or blast to Sa 2 of at least 70% of the surface. For coated surfaces ensure the substrate is clean, dry and undamaged. Ensure the previous coat is compatible.

Optimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation. Apply via airless spray. Use a brush or roller for stripe coating or small areas. Care must be taken to achieve the specified dry film thickness.

Technical Details

Approvals

  • Norsok M-501 System 1 (Pre Qualified)
  • Norsok M-501 System 2A
  • Norsok M-501 System 7B (Pre Qualified)

Technical Info

Components: Two Part
Type: Amine cured epoxy coating
Finish: Semi Gloss
Stock Colours: Grey and Red
Tintable: Call to Check. Please note, bespoke tints are non refundable / exchangeable.
VOC Content: 229.0g per Litre
Volume Solids: 75%
Suitable Substrates: For properly prepared carbon steel, stainless steel, aluminium, galvanised steel and thermally sprayed zinc substrates
Application Method: Airless Spray. Use a brush or roller for stripe coating or small areas.
Theoretical Coverage: 1.5 - 7.5 m2 per litre
Wet Film Thickness (WFT): 133 - 667 microns
Dry Film Thickness (DFT): 100 - 500 microns
Induction Time: 10 mins at 23°C
Pot Life: 1 hour at 23°C
Touch Dry: 3 hours at 23°C
Overcoatable: 3 hours at 23°C
Fully Cured: 10 days at 23°C
Cleaner / Thinner: Jotun Thinner No. 17
Shelf Life: Part A: 12 months, Part B: 24 months
Packaging: Available in 20 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use