£7.75 delivery on orders excluding certain products & postcodes *

Sales & Technical 01462 421 333
Search
My Cart

Sherwin Williams Epidek M153 - Formerly Leighs

SKU
id4166
Part A: UN1263 (Class: 3, Pk Grp: III), Additive: UN3469, (Class: 3, Pk Grp: II)
A hard wearing, anti slip extra heavy duty deck coating system. Reaches NORSOK M-501 and BS.476 Part 7: Surface spread of flames
Available in 12.6 Litres
From £285.85 £238.21
In stock
Only %1 left
main product photo
Product Description

Sherwin Williams Epidek M153 is a hard wearing, tar free, anti slip, pure epoxy based extra heavy duty deck coating system. Provides exceptional wear and impact resistance to deck surfaces including those in extreme conditions.

Best Uses

Sherwin Williams Epidek M153 provides excellent resistance to crude oil and salt water immersion, and when combined with calcined bauxite aggregate dressing this product can offer exceptional resistance to abrasion and impact damage. As a product with a long expected lifespan, Epidek M153 demonstrates good resistance to the localised effects of heat when welding repairs or modifications occur during construction and maintenance.

Epidek M153 can be used to level out undulations and fill cracks in steel decks and plates, and is also suitable for areas when a high level of anti slip rating are required under conditions of severe crude oil and hydrocarbon contamination. Suitable for walkways, escape routes and lay down areas.

Application

Material should be applied direct to blast cleaned steel prepared to a minimum standard of Sa2 1/2 BS EN ISO 8501-1:2007. Ensure surfaces to be coated are clean, dry and free from all surface contamination. Mix contents of epoxy resin and curing agent together thoroughly. Add the fine silica grit (component A using a power stirrer. Apply product using a trowel to a wet film thickness of 3mm. Within 10-20 mins dress the Epidek M153 aggregate onto the screed until it is fully saturated and no screed is visible.

Technical Details

Approvals

  • Norsok M-501 System 4 (Pre Qualified)

Benefits of Epidek M153

  • Low smoke emission and reduced health and safety impact
  • Increases anti slip properties and greatly extends service life
  • Improved mixing and application properties
  • Excellent adhesion to epoxy primers, tie coats or blast cleaned steel
  • Exceptional wear and greatly extends service life
  • corrects undulations in steel decks or fills cracks between horizontal deck plates
  • NORSOK qualified M-501 Rev.5 (Test reports 4-11-11-10)
  • BS.476 Part 7: Surface spread of flames

Technical Info

Components: Four Pack
Type: Coal Tar Free, Solvent Less Epoxy
Finish:  
Stock Colours:

Dark Grey and Green

Dressing aggregate available as standard grey or photo-luminescent green.
Tintable: No
VOC Content: 42 g/L
Volume Solids: 95%
Suitable Substrates: Blast Cleaned Steel
Application Method: Trowel
Theoretical Coverage: 0.32 m2 per litre at 3000 microns
Wet Film Thickness (WFT): 3158 microns
Dry Film Thickness (DFT): 3000 microns
Induction Time: -
Pot Life: 1.5 hours at 15°C
Touch Dry: 6 hours at 15°C
Overcoatable: After 6 hours at 15°C
Dry to Handle: 20 hours at 15°C
Cleaner / Thinner: Sherwin Williams Thinner C5
Shelf Life: 2 years minimum in original unopened containers.
Packaging: Available in 12.6 Litres
Product Data Sheet (264.64 kB)
Safety Data Sheet - Part A (173.88 kB)
Safety Data Sheet - Part B (242.54 kB)
Safety Data Sheet - Part C (142.11 kB)
Safety Data Sheet - Part D (146.51 kB)
System Info - Project Job Sheet (89.24 kB)

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use