*Mapei Mapefloor FC 200 EU

Please note, this product is currently unavailable. Contact our technical team for more info.

Mapei Mapefloor FC 200 EU is a high solid content, two-component, epoxy-based resin, which is used to create a seamless smooth, or non-slip floor coating. The product is classified by FeRFA “Type 3 : High build floor coating”.

Best Uses

Mapei Mapefloor FC 200 EU is ideal for use in a number of different areas, including: car parks, warehouses, shopping centres, factories, workshops, garages and hangars. Mapefloor FC 200 EU is also suitable for use in chemical and pharmaceutical industries.

The product complies with the requirements according to EN 13813 "Screed material and floor screeds - Screed material - Properties and requirements", which defines the requirements to be applied to materials for screeds used in the construction of internal floors. 

Application

Preparation of the substrate

The surface of the concrete must be dry, clean, and sound with no crumbling or detached areas. The compressive strength of the concrete used for the substrate must be at least 25 N/mm² and its tensile strength must be at least 1.5 N/mm². The strength of the substrate must also be suitable for its final use and for the types of loads acting on the flooring. The level of moisture in the substrate must be a maximum of 4% and there must be no capillary rising damp.

The surface of the floor must be prepared with suitable power tools (e.g. shot-blasting or grinding with a diamond disk) to remove all traces of dirt, cement laitance, and crumbling or detached portions and to leave a dry and dust-free open textured surface. Before applying the product, remove all dust from the surface with a vacuum cleaner. Any defects present in the surface, such as holes, pitting, cracking, etc., must be repaired with PRIMER SN fillerized with quartz sand or made thixotropic with Additix PE, or with Mapefloor JA or Mapefloor JA Fast depending on the width and depth of the defects or cracks.

Reintegrate any badly damaged areas or joints, fill hollows in the surface, and repair or carry out localised modifications to slopes with Mapefloor EP19 ready-mixed epoxy mortar.

Application of the primer

Apply Primer SN or Mapefloor I 900 neat, by roller or mixed with 20% by weight of Quartz 0.5, with a straight trowel or rake on the substrate after it has been prepared as specified. It is suggested to broadcast the layer of primer, while still wet, with quartz sand Quartz 0.5.

Preparation of the product

The two components which make up Mapecoat FC 200 EU must be mixed together just before application.

Application of the product

Mapefloor FC 200 EU can be used as a smooth or non-slip coating system.

1. Roll coat epoxy resin system: When the layer of primer is completely hardened, apply the finishing coat of Mapefloor FC 200 EU by straight trowel or squeegee down to a feather edge on the surface, then back roll crosswise with a short pile roller. As an alternative method, the product can be directly applied on the substrate by medium pile roller.

2. Multi-layered non-slip system: When the layer of primer is completely hardened, pour Mapefloor FC 200 EU onto the floor and spread it out evenly with a straight trowel or roller. While the product is still wet, fully broadcast with Quartz 0.5. If a higher degree of non-slip finish is required, a larger particle size has to be used. In such cases, the consumption rate of the following coat will be higher. When the first coat of Mapefloor FC 200 EU has hardened, remove any excess sand by sweeping, then thoroughly remove the last grains by vacuuming. Apply the finishing coat of Mapefloor FC 200 EU by straight trowel down to a feather edge, then back roll crosswise with a short pile roller. As an alternative method, the product can be directly applied by a medium pile roller. Make sure the roller strokes crisscross to get a better finish.