Mapei Purtop Easy T

Single pack transparent aliphatic polyurethane waterproofing membrane for terraces and balconies.

Available in 15 Kg in Transparent

* These colours are for guidance only. Variations between output devices can misrepresent the appearance of an actual colour. Also, we strongly advise that you order your complete paint requirements simultaneously to ensure a uniform batch colour.

2. Size

3. Select a Qty

As low as:

£240.49

Inc VAT £288.59

PRODUCT DETAILS

Mapei Purtop Easy T is a single component transparent aliphatic polyurethane waterproofing membrane for terraces and balconies.

Best Uses

Purtop Easy T is a one-component, transparent, aliphatic polyurethane waterproofing membrane formulated ito be suitable for coating old tiled surfaces with infiltrations used by pedestrian traffic. Once applied, in just a few hours Purtop Easy T forms a seamless, elastic membrane with no overlaps and excellent crack-bridging properties which is able to withstand normal dynamic stresses acting on balconies and terraces.

Forms a highly elastic and durable membrane
An aliphatic product and remains stable against UV rays
One-component, ready-to-use product and is very easy to apply
Does not require any reinforcement

Application

Preparation of the substrate
Old floors in ceramic, porcelain, klinker, etc. must be well bonded to the substrate and must be completely free of any substances which could affect adhesion, such as grease, oil, wax, paint, etc.

The grouts between the tiles must be sound and in good condition. If they are partially damaged or loose, remove the grout and fill the grouts in the floor with a suitable product from the MAPEI range before applying Purtop Easy T. Apply Purtop Easy T Primer by going over the entire surface with a clean rag dipped in the primer.

Preparation of the product
Purtop Easy T is a one-component, ready-to-use product but it is recommended to mix it before use to make sure it is perfectly blended.

Application of the product
When Purtop Easy T Primer is dry, apply Purtop Easy T. The temperature of the substrate must be at least 3°C above dew-point and the level of residual moisture must be no higher than 4%. Apply at least two even coats of Purtop Easy T with a roller or trowel to form a total thickness of around 1 mm. Purtop Easy T may also be applied by airless spray but must be diluted with 5% of Mapei Thinner PU.

Purtop Easy T has a smooth finish. To obtain a finish with a non-slip effect, apply two coats of Purtop Easy T and leave them to dry. Then, when the second coat is dry, lightly broadcast the surface with Mapei Quartz 0.25 and apply a thin coat of Purtop Easy T with a roller, making sure to criss-cross the roller strokes so that the quartz sand is distributed evenly.

IMPORTANT NOTICE: From 24th August 2023, adequate training is required before industrial or professional use of this product. Training can be accessed at: https://www.safeusediisocyanates.eu

TECHNICAL

Components:	One Part
Type:
Finish:
Stock Colours:	Transparent
Tintable:	No
VOC Content:
Volume Solids:
Suitable Substrates:	Old floors in ceramic, porcelain, klinker, etc.
Application Method:	Roller, Trowel or Airless Spray
Theoretical Coverage:	1 kg/m² corresponds to a coat around 1 mm thick. In general, the consumption rates below are for a seamless film on a flat surface and could be higher on uneven substrates.
Wet Film Thickness (WFT):
Dry Film Thickness (DFT):
Induction Time:	-
Pot Life:	-
Touch Dry:	2 - 4 hours at 18°C
Overcoatable:	4 hours at 18°C
Fully Cured:	1 month at 18°C
Cleaner / Thinner:	It is recommended to clean tools with water before the product starts to set. Once hardened, cleaning is much more difficult and must be carried out mechanically.
Shelf Life:	12 months in its original packaging in a dry, covered area at a temperature of between +5°C and +35°C.
Packaging:	Available in 5 Kg