Remmers Epoxy ST 100

SKU
id21916
Part A: UN3082 (Class: 9, Pk Grp: III), Part B: UN2735 (Class: 8, Pk Grp: III)
A transparent priming and mortar resin floor primer for use within the Remmers OS 8 System.
Available in 10 and 25 Kg
From £197.76 £164.80
In stock
Only %1 left
Product Description

Remmers Epoxy ST 100 is a transparent priming and mortar resin floor primer for use within the Remmers OS 8 System.

Best Uses

Remmers Epoxy ST 100 is an unpigmented epoxy resin binder that is used as an impregnation agent, primer, bonding layer, levelling layer and for the production of compression resistant mortars, flow covers and as a blinding layer for blinded covers.

  • Low viscosity
  • Good penetration capacity
  • Plasticiser free
  • Nonylphenol and alkyl phenol free
  • Can be subjected to mechanical loads
  • Can be subjected to chemical loads

Remmers Epoxy ST 100 application examples include flooring in consumer markets, workshops, stairs with heavy traffic, production halls, assembly areas, shipyards and warehouses for heavy goods.

Application

The substrate must be load-bearing, form-stable, sound, free of loose constituents, dust, oil, grease, rubber marks and other substances with a separating effect. Tensile strength of the surface of the substrate must be 1.5 N/mm² on average and compressive strength at least 25 N/mm². The substrate must have achieved its moisture balance and be protected from the effects of moistures from behind, also during utilisation.

  • Concrete max. 4% by mass
  • Cement screed max. 4% by mass
  • Anhydrite screed max. 0.3% by mass
  • Magnesite screed 2 - 4% by mass

In the case of anhydrite and magnesite screeds it is essential that the penetration of moisture from building elements or the ground is not possible.

Prepare the substrate by suitable means, e.g. steel ball jetting or diamond grinding so that it meets the specified requirements. Fill broken out or missing areas in the substrate with the Remmers PCC System or Remmers EP Mortars flush with the surface.

Tin container:
Add the entire quantity of the hardener (comp. B) to the basic component (comp. A). Mix thoroughly with a slow speed electric mixer (max. 300 - 400 rpm). The fill the mixture into a separate container and mix again thoroughly. In the case of filled systems, the cor-responding quantity of filler is added to the epoxy resin mixture while mixing slowly. Mix thoroughly.

Multi-chamber bag:
Open the outer packaging at the notch and take out the transparent, multi-chamber bag. Remove the divider clip on the 2-component bag. Then mix the two components together in the bag thoroughly by kneading the bag (approx. 60 sec.) Then pour the thoroughly mixed material over the prepared surface and distribute with a suitable tool.

See product data sheet for application examples and methods.

Technical Details

Systems

  • Remmers SS350PH+ - Epoxy Self Smoothing System with Performance Seal (DFT = 2-3mm)
  • Remmers 356WHG - Epoxy Conductive with Excellent Chemical Resistance System (1.5 - 2mm)
  • Remmers 361DQ - Floormix DQ Decorative Epoxy Floors and Walls System (3 - 4mm)

See technical tab for downloadable System Sheets.

Technical Info

Components: Two Pack
Type: Epoxy Resin Binder
Finish:  
Stock Colours: Transparent
Tintable: No
VOC Content: <500 g/L
Volume Solids:  
Suitable Substrates: For flooring within the Remmers OS 8 System
Application Method: Smoothing Trowel, Spiked Roller
Theoretical Coverage: Dependant on Application - See data sheet
Wet Film Thickness (WFT): Dependant on Application - See data sheet
Dry Film Thickness (DFT): Dependant on Application - See data sheet
Induction Time: -
Pot Life: -
Surface Dry: 25 minutes at 20°C
Overcoatable:  
Fully Cured:  
Cleaner / Thinner: Remmers V101 Thinner
Shelf Life: At least 12 months in unopened and unmixed, original containers stored cool but frost-free
Packaging: Available in 10 and 25 Kg

Related Products