ResDev Pumatect

A two part gloss, epoxy floor coating. A tough, hard wearing finish for medium duty traffic floors. FeRFA Type 3 Approved.

Available in 5 and 15 Kg

* These colours are for guidance only. Variations between output devices can misrepresent the appearance of an actual colour. Also, we strongly advise that you order your complete paint requirements simultaneously to ensure a uniform batch colour.

2. Size

3. Select a Qty

As low as:

£60.69

Inc VAT £72.83

PRODUCT DETAILS

ResDev Pumatect is a two part, High Build, solvent free epoxy floor paint. It offers a tough, hard wearing gloss finish which provides good wear resistance for warehouse floors, garages and car parking spaces.

Best Uses

ResDev Pumatect is a two pack virtually solvent free epoxy industrial floor paint offering excellent abrasion and chemical resistance. Pumatect provides a tough, high build, hard wearing coating for medium duty traffic giving a high film finish which is suitable for warehouse floors, garages and even car parking spaces.

This product also can be used in Aircraft Hangars and has reasonable resistance with short term contact to Skydrol in conjunction with an effective cleaning regime.

Protects concrete from oil and chemical spillages
High build with excellent wear resistance
Virtually solvent free
Available in a wide range of colours
Glossy easy to clean finish
Non-dusting
Slip-resistant options available

ResDev Pumatect is formulated for use on medium duty floors requiring an easy to clean, tough and durable coating with excellent chemical resistance, such as warehouses, factories, workshops, showrooms, packing and storage areas. Pumatect can also be used as a seal coat for broadcast systems such as intermediate car park decks. ResDev Pumatect is suitable for regular foot traffic, fork lift truck traffic and occasional hard plastic-wheeled trolleys.

BS 8204 Part 6 Synthetic Resin Flooring Type Categorisation

FeRFA No	Type	Description	Duty	Typical Thickness
1	Floor Seal	Applied in 2 or more coats. Generally solvent or water borne	LD	> 150μm
2	Floor Coating	Applied in 2 or more coats. Generally solvent free	LD / MD	150 - 300μm
3	High build floor coating	Applied in 2 or more coats. Generally solvent free.	MD	300 - 1000μm
4	Multi-layer flooring	Aggregate dressed systems based on multiple layers of floor coatings or flow-applied flooring, often described as sandwich systems	MD / HD	> 2mm
5	Flow-applied flooring	Often referred to as ‘self-smoothing’ or ‘self-levelling’ flooring and having a smooth surface	MD / HD	2 - 3mm
6	Resin screed flooring	Trowel-finished, heavily filled systems, generally incorporating a surface seal coat to minimise porosity	MD / HD	> 4mm
7	Heavy duty flowable flooring	Having a smooth surface	HD / VHD	4 - 6mm
8	Heavy duty resin flooring	Trowel-finished, aggregate filled systems effectively impervious throughout their thickness.	VHD	> 6mm

LD – light foot traffic, occasional rubber tyre vehicles, MD – regular foot traffic, frequent fork lift truck traffic, occasional hard plastic-wheeled trolleys, HD – constant fork lift truck traffic, hard plastic wheeled trolleys, some impact, VHD – severe heavily loaded traffic and impact

Application

Substrates in contact with the ground must incorporate a functional damp proof membrane in accordance with CP102 or, in the case of basement floors, BS 8102. The base should have a relative humidity at the surface of no more than 75% when measured according to BS 8203. See data sheet for full preparation guidance.

Substrates must be clean, dry and free of surface laitance and contaminants such as dirt, oil, grease, poorly bonded coatings and surface treatments. Inadequate preparation will lead to loss of adhesion and failure. In coatings, there is a tendency for the finish to mirror imperfections in the substrate. Grinding, or light vacuum-contained shot-blasting, is therefore preferred over planing for these systems.

Mixed material must be used immediately. (minimum 15°C). Apply with a medium pile simulated sheepskin roller, working well into the surface, taking care not to exceed the coverage rate. Edges and difficult to reach areas may be applied thinly by brush. An anti-slip finish may be achieved by broadcasting the first coat to saturation, with kiln dried silica sand at 3 - 4 kg/m2. Allow the first coat to cure for 24 hours at 15°C (or longer in colder temperatures) then remove all excess sand with a stiff broom and vacuum. Apply a second coat to encapsulate the grains.

TECHNICAL

Approvals

Certified for FeRFA Type 3: High Build Floor Coating; Medium Duty; 300 - 1000 microns.

Technical Info

Components:	Two Pack
Type:	Epoxy
Finish:	Gloss
Stock Colours:	Mid Grey and Light Grey
Tintable:	Yes, to most RAL or British Standard codes. Please note, bespoke tints are non refundable / exchangeable
VOC Content:	<500 g/L
Volume Solids:
Suitable Substrates:	Concrete and polymer modified cementitious screeded floors
Application Method:	Medium Pile Sheepskin Roller
Theoretical Coverage:	1st coat - 375 g/m2 2nd coat - 250 g/m2
Wet Film Thickness (WFT):
Dry Film Thickness (DFT):	Approximately 400 microns from two coats
Induction Time:	-
Pot Life:	25 minutes at 20°C
Cure Time To Pedestrain Traffic:	24 hours at 20°C
Overcoatable:	Between 16 - 36 hours at 20°C
Fully Chemical Resistance:	7 days at 20°C
Cleaner / Thinner:	Tools and equipment should be cleaned whilst the resin is still wet with a suitable solvent.
Shelf Life:	12 months if stored in accordance with the above recommendations.
Packaging:	Available in 5 Kg and 15 Kg. Other sizes available on request.