Sherwin Williams Dura-Plate 301W Surface Tolerant

SKU
id12841
Part A: UN3082 (Class: 9, Pk Grp: III), Part B: Non Hazardous
An M24 spec low temperature curing, surface and humidity tolerant two pack modified epoxy anti corrosive coating for long life steel protection.
Available in 4 and 16 Litres
From £115.87 £96.56
In stock
Only %1 left
Product Description

Sherwin Williams Dura-Plate 301W is a 0°C low temperature, surface and humidity tolerant 2 pack modified epoxy anti corrosive coating. XM92/M24/ 196 spec.

Best Uses

Dura-Plate 301W is an M24 spec. low temperature curing, surface and humidity tolerant two-pack modified epoxy. It can be applied without dew point restrictions and over wet steel surfaces. 301W shows good chemical and abrasion resistance and good edge-retentive properties. It can be applied over steel prepared by hydro-blasting, grit blasting or mechanical tooling.

This product has excellent edge retention, no dew point or relative humidity restrictions, excellent anti-corrosive properties, can be applied over wet substrates, can be applied over medium flash rust and has excellent substrate and intercoat adhesion. DURA-PLATE 301W is an anti-corrosive coating for long service life steel protection.

It can be used for both immersion and above the waterline service in marine, offshore, construction and industrial applications. It is suitable for new building, conversion, repair or maintenance applications. It provides superior performance protecting areas such as ballast tanks, void tanks, crude oil tanks, slop tanks, mud pits, wet spaces, bilges, decks, external hull and steel bridges.

Application

Surface must be clean and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion. DURA-PLATE 301W is tolerant to hydroblasted, wet or dry abrasive blasted or mechanically prepared surfaces. Applicable via airless spray or brush for stripe coats or touch up on small areas.

Technical Details

Approvals

  • Dura-Plate 301W is approved for Network Rail maintenance specification
  • Certificate No’s XM92-M34-197, XM92-M34-200, XM92-M34-201, XM92/M24/ 196

Technical Info

Components: Two Pack
Type: Modified Epoxy
Finish: Semi-Gloss
Stock Colours: Light Grey or Off-White
Tintable: Limited Range. Please note, bespoke tints are non refundable / exchangeable
VOC Content: <100 g/l
Volume Solids: 97 ± 3%
Suitable Substrates: Steel
Application Method: Brush, Airless Spray
Theoretical Coverage: 9.7me per litre for 100 microns, 3.3m2 per litre for 300 microns
Wet Film Thickness (WFT): 103 - 309 microns
Dry Film Thickness (DFT): 110 - 300 microns
Induction Time: -
Pot Life: 30 minutes at 20°C
Touch Dry: 4.5 hours at 20°C
Overcoatable: After minimum 8 hours at 20°C
To Handle: 20 hours at 20°C
Cleaner / Thinner: TH03
Shelf Life: 12 months from date of production unopened
Packaging: Available in 4 Litres and 16 Litres
Product Video

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use