Teknos Kirjo Aqua Paint

SKU
id18722
Non Hazardous
For new unpainted zinc coated/galvanized sheet-iron and steel surfaces.
Available in 0.9, 2.7, 9 and 18 Litres
From £37.74 £31.45
In stock
Only %1 left
Product Description

Teknos Kirjo Aqua is a water-borne acrylate-based paint with anti-corrosive pigmentation for sheet-iron roofs.

Best Uses

Kirjo Aqua ia best used for new unpainted zinc coated/galvanized sheet-iron and steel surfaces and also for maintenance painting of sheet-iron roofs which are previously painted with alkyd or acrylate paints.

KIRJO AQUA can also be used for maintenance painting of industrially paint coated sheet steel: polyurethane, PURAL, PUREX, polyester, acrylic and PVC-Plastisol coatings. Maintenance painting of other coatings is done in accordance with instructions given by the steel manufacturer..

Application

Before use stir the paint thoroughly. Dilute the paint 5 - 15 % by volume by water, when required.

NEW UNPAINTED SURFACES: Apply the paint by brush, roof brush or airless spray. When applied by a brush, apply the paint twice to a dry film thickness of 2 x 40 μm.
When spray painting the total film thickness of 80 μm (wet film abt. 210 μm) may be applied as a single coat. Recommended nozzle for airless spray is 0.015 - 0.019".

MAINTENANCE PAINTING: Bare, rust-free sheet-iron surfaces of the cleaned, damaged areas are touched up with KIRJO AQUA. Very rusty, cleaned steel surfaces are primed with Teknos Ferrex Aqua Anti-corrosive Paint. The whole roof is then painted with Kirjo Aqua to a dry film thickness of 40 μm. Two coats are recommended only if the colour of the roof is changed.

The surface to be painted must be dry. During the application and drying period (note also the temperature of the night following the painting) the temperature of the ambient air, the surface and the paint needs to be above +10°C and the relative air humidity below 80%. If the temperature of the surface to be painted exceeds +40°C, the application properties and the adhesion of the paint deteriorate. The temperature of the surface must not be over +40°C, or the water in the product may evaporate too quickly, pores may be formed to the paint film, adhesion may get worse or bubbles may appear.

Technical Details
Components: Single Pack
Type: Water-borne acrylate-based paint
Finish: Matt
Stock Colours: T2504 Graphite Grey, T2509 Red, T2511 Dark Red, T2514 Brown and T2515 Black
Tintable: No
VOC Content: 140 g/l
Volume Solids: About 38 % by volume
Suitable Substrates: Sheet-iron roofs, new unpainted zinc coated/galvanized sheet-iron and steel surfaces
Application Method: Brush or Spray
Theoretical Coverage: 7 - 8 m²/l, abt. 40 μm dry film, applied once with brush.
Wet Film Thickness (WFT): 210 μm
Dry Film Thickness (DFT): 40 μm
Induction Time: -
Pot Life: -
Dust Free 1 hours at 23°C
Overcoatable: After 8 hours at 23°C
Fully Cured: -
Cleaner / Thinner: Water. Wash the equipment immediately after use with appropriate detergent and warm water
Storage: Must not freeze
Packaging: Available in 2.7, 9 and 18 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use