
Thermoguard Wallcoat Insulating Basecoat
Thermoguard Wallcoat Insulating Basecoat is formulated for use under Thermoguard Wallguard SFR (Smoke & Flame Retardant)
Best Uses
Thermoguard Wallcoat Insulating Basecoat is a water based intumescent coating ideal for use in a fire protective coating system on walls and ceilings internally or external. Provides exceptional adhesion to bare or painted plaster, concrete and masonry substraights.
- As part of a system, achieves EN Class B s1 d0 spread of flame on walls and ceilings including surfaces coated with high risk multiple layers of paint
- Permanent protection
- Tintable upon request to undercoat shades
- Water-based low VOC
In the event of a fire, Thermoguard Wallcoat Insulating Basecoat expands, forming a heat-resistant char to insulate the surface. Suitable for overcoating with Thermoguard Wallguard SFR Matt or Eggshell.
Application
All surfaces must be clean and dry. Remove all possible surface contaminates such as grease, smoke residues, silicates etc. Seal water-stain risks with stain blocking sealer. Abrade hard or smooth surfaces with wetted 120 grit wet-or dry abrasive or dust extracting abrader. Rinse off slurry while still damp. When dry, remove any loose or suspect material back to firm edge. Fill and repair any damage to the substrate using a good quality remedial filler.
Apply one coat of Thermoguard Wallcoat Insulating Basecoat at the tin spread rate. When suitably dry (see Product Data Sheet), overcoat with Thermoguard Wallguard SFR. Apply at rate stated on specification to protect surfaces and enable project certification - contact our Technical Team for guidance. Suitable for application via brush, woven fabric roller sleeves and synthetic bristle brushes / roller. For application via conventional spray, ensure all traces of solvent flushed out. Adjust fluid flow and air flow as normal for acrylic emulsion paint. For airless spray applications, use 3/8 inch line, 30 mesh filter on machine, no filter in gun with a 0.17 to 0.21 tip. PSI 1500 to 1900
Ensure coverage is applied as per can i.e., 25 sqm can covers 25 sqm.
IMPORTANT INTUMESCENT PRODUCT NOTE: Always contact Promain’s technical team prior to purchase to obtain a tailored project specification and the advice necessary. The information displayed on this website should only be used as a guide. Promain will not be held liable for any resulting damage to property, human life or monetary costs incurred due to incorrect specification, preparation, application or maintenance that has occurred due to negligence by either the purchaser or applicator. This includes your failure to have contacted us to obtain the relevant advice/specification.
Test Results
- FIRE TEST STANDARDS in UKAS and EOTA accredited Fire Test laboratory
- BS EN Class B s1 d0 "best in class" supercedes old Class 0
Technical Info
| Components: | Single Pack |
| Type: | Water Based |
| Stock Colours: | White |
| Tintable: | Yes, undercoat shades upon request. Please note, bespoke tints are non refundable / exchangeable. |
| Suitable Substrates: | Interior walls and ceilings |
| Cleaner / Thinner: | Clean equipment immediately after use with water. |
| Shelf Life: | see container |
| Packaging: | Available in 25m2, 50m2 and 100m2 tins |
| VOC Content: | 16 g/l |
| Application Method: | Airless Spray, Brush, Conventional, Roller |
| Theoretical Coverage: | A 25m2 tin needs to cover 25m2 for certification |
| Finish: | Smooth |
| Touch Dry: | 1 hour at 20°C |
| Volume Solids: | 60% |
| Overcoatable: | 4 hours at 20°C |
| Wet Film Thickness (WFT): | Please contact Promain's Technical Team |
| Dry Film Thickness (DFT): | Please contact Promain's Technical Team |
| Induction Time: | Please contact Promain's Technical Team |

