Axalta ViterFloor 276 (Formerly Spencer Coatings) is a single pack, gloss, polyurethane floor coating for general purpose and light traffic areas.
Axalta ViterFloor 276 is a single pack, economic, easily applied floor coating that consists of a mild solvent blend to minimise reaction with existing floor coatings and minimise the lifting of old coating edges. This single pack PU floor paint is ideal for concrete and wooden floors.
ViterFloor 276 is an easy to use maintenance paint for light duty areas in shops, warehouses and industrial units. This product benefits from being able to be brush or roller applied for easy routine floor repainting.
All surfaces must be clean, dry, and free from grease, oil, laitance, dust and other contamination.
Bare Concrete: Remove dirt and contamination by detergent washing, flame cleaning or other appropriate means. For the best long term coating life, laitance should be removed by vacuum blast cleaning (recommended), power grinding or acid etching. If acid etching, more than one application may be required to produce a granular surface suitable for good adhesion. Vacuum blast cleaning should produce a surface profile appropriate to the thickness of the coating being applied. If laitance is not removed, it can detach in service along with the coating, leaving patchy areas of bare concrete.
Previously Painted Floors: abrading (as well as thoroughly cleaning) the existing coating is always recommended to optimise adhesion. As ViterFloor 276 has a mild solvent blend, there should be minimal reaction with existing coatings such as the lifting of old coating edges. A test area is recommended to confirm compatibility and that adequate adhesion can been achieved.
Wood Floors: Punch all nail heads down below the surface. Sand the surface down to clean, smooth wood using an industrial vacuum sander, cutting-in at edges with a hand sander. To give a smooth finish it is recommended to also lightly sand and vacuum between coats.
Steel Floors: Consult our technical team.
Must be mixed thoroughly by using a mechanical agitator before use. Agitate periodically to ensure paint remains homogeneous.
The concrete surface must be dry and at least 12 weeks old. The moisture content of the concrete should not exceed 6% when measured 25mm below the surface (with e.g. a Protimeter measuring in 25mm drilled holes filled with gel), or 14% when measured with a surface moisture gauge (such as a Protimeter WME (Wood Moisture Equivalent) gauge).
Only apply in conditions of good ventilation which must be maintained during drying and curing. Do not apply when rain, mist, sleet or snow are imminent. During application and drying time of the paint coating, the surface should be dry, the Relative Humidity should not exceed 85% and the substrate temperature should remain at least 3oC above the dew point. Paint temperature should ideally be at a minimum of 15ºC.
|Stock Colours:||Just tints.|
|Tintable:||Yes, to most RAL or British Standard codes. Please note, bespoke tints are non refundable / exchangeable|
|VOC Content:||462 g/L|
|Suitable Substrates:||Concrete, Wood
|Application Method:||Brush, Roller|
|Theoretical Coverage:||9 - 15 m2 per litre|
|Wet Film Thickness (WFT):||67 - 111 microns|
|Dry Film Thickness (DFT):||30 - 50 microns|
|Dust Dry:||3 hours at 23°C with 40 microns DFT|
|Overcoatable:||Overcoat either wet-on-wet, or after a minimum of 16 hours at 20oC. After 3 days at 20oC, light abrasion will be necessary in order to achieve optimum adhesion|
|Fully Cured:||7 days at 23°C with 40 microns DFT|
|Cleaner / Thinner:||Axalta 1050 Thinner|
|Shelf Life:||Minimum 12 months if stored as above in unopened containers|
|Packaging:||Available in 5 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.