Tikkurila Temafloor P300 2 Part Solvent Free Epoxy Coating

SKU
ID9994
Part A: UN3082 (Class: 9, Pk Grp: III), Part B: UN2289 (Class: 8, Pk Grp: III)
For use on concrete floors in industrial and storage facilities, repair shops.
Available in 10 Litres. Tintable to RAL, NCS, SSG, BS, MONICOLOR NOVA and SYMPHONY colour cards
From £119.51 £99.59
In stock
Only %1 left
Product Description

Tikkurila Temafloor P300 is a two component, solvent free, self levelling epoxy coating formulated for treating new and old concrete industrial floors.

Best Uses

Tikkurila Temafloor P 300 can withstand heavy mechanical and chemical stress in industrial, commercial and storage facilities, repair shops, factories, sports arenas, warehouses, car parks, pharmaceutical premises, public and commercial buildings and more. As this product is self levelling, artistry can be used to produce an individual and colourful flooring coating design using various colours.

Application

Temafloor P 300 is a self-levelling coating, that can be applied with an adjustable steel trowel. The relative humidity of the concrete should not exceed 97%. The temperature of the ambient air, surface or coating should not fall below + 15ºC during application or drying. Relative humidity of air should not exceed 80%.

For New Concrete: Remove laitance by power grinding, vacuum grit blasting or hydrochloric acid etching. Choose the method best suited for the premises. After grinding remove dust carefully with a vacuum cleaner. Hydrochloric acid etching is carried out with diluted hydrochloric acid (1 part concentrated hydrochloric acid, 4 parts water). Rinse with plenty of water. Dry the floor.

For Old Concrete: Remove all grease, oil, chemicals and other impurities by MAALIPESU detergent. Remove old peeling paint layer by grinding or vacuum grit blasting. Choose the method best suited for the premises. Clean out pot-holes removing all loose friable material. Open cracks with e.g. an abrasive tool. Remove loose material and dust.

Prime using 30–50% with Thinner 1029 (or 1031) thinned Temafloor 200 Primer or 400 epoxy varnish. Pour the varnish mixture onto the floor and apply as much as is needed to impregnate the concrete surface. If necessary, repeat priming to get a non-porous surface. Subsequent treatment can be carried out after 2 hours using "wet-on-wet" technique. A porous priming coat will result in holes and air bubbles in the finished screed. Mix the correct proportions of base and hardener thoroughly (approx. 2 minutes) by using a low speed hand drill with a paddle. The amount of mixture depends on the area to be coated and on the pot life of the mixture. Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the coating and risk the success of the application.

Technical Details

Approvals

  • LuL APR Reg No. 4352 - Epoxy floor coating for mineral surfaces. Solvent Free Epoxy system. Suitable to paint on cementitious surfaces. Complies with LU Standard 1-085 'Fire Safety Performance of Materials' and can be used in sub surface areas.
  • Fire classification according to standard EN 13501-1 is BFL-s1

Features

  • Temafloor P 300 for use on concrete floors in industrial and storage facilities, repair shops; e.g. process or paper machine units and corridors and bunds
  • Good resistance to abrasion, withstands water, oils, greases, chemicals and dilutesolutions of non-oxidizing acids, alkali and salt solutions
  • Resists only temporary splashes of oxidizing acids and bleaching chemicals
  • Withstands +70ºC dry heat and +60ºC in immersion

Technical Info

Components: Two Part
Type: Solvent Free
Finish: Gloss
Stock Colours: Just tints
Tintable: RAL, NCS, SSG, BS, MONICOLOR NOVA and SYMPHONY colour cards. Temaspeed Premium tinting. Also metallic shades are available. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 500.0g per Litre
Volume Solids: 100%
Suitable Substrates: For new and old concrete floors exposed to heavy mechanical and chemical stress
Application Method: Spiked Roller
Theoretical Coverage: m2 per litre at microns
Wet Film Thickness (WFT): 0.3–0.5 mm
Dry Film Thickness (DFT): 0.3 mm
Induction Time: -
Pot Life: 20–30 minutes on substrate, approx. 15 minutes in the mixing container.
Dust Dry: 6 hours at 23°C
Overcoatable:  
Fully Cured: 7 days at 23°C
Cleaner / Thinner: Do not thin.
Shelf Life:  
Packaging: Available in 10 Litres

Related Products