Hempel Hempatex Hi-Build 46410 Container Paint

SKU
id21245
UN1263 (Class: 3, Pk Grp: III)
A primer, intermediate or finishing coat in Hempatex systems in moderately corrosive environment.
Available in 5 and 20 Litres. Tintable to many RAL and BS shades.
From £32.77 £27.31
In stock
Only %1 left
Product Description

Hempel Hempatex Hi-Build 46410 is formulated as a primer, intermediate or finishing coat in Hempatex systems in moderately corrosive environment. Suitable for use as a finishing coat on containers.

Best Uses

Hempel Hempatex Hi-Build 46410 is a physically drying high build paint with good colour retention as a flat finish. Based on acrylic resin and non-chlorinated plasticizer.

Hempel Hempatex Hi-Build 46410 is formulated as a primer, intermediate or finishing coat in Hempatex systems in moderately corrosive environment. Hempel Hempatex Hi-Build 46410 is suitable as a self-primed repair and touch-up coating for containers as well as other cases where a fast and economic repair job is desired. It is also suitable as a finishing coat for containers.

Hempel Hempatex Hi-Build 46410 contains zinc phosphate. Hempel Hempatex Hi-Build 46410 is resistant to salt water, splashes of aliphatic hydrocarbons, animal and vegetable oils.

Application

Preparation of New Steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Abrasive blasting to the cleaning degree specified for the final coating system, usually Sa 2½ (ISO 8501-1:2007). Apply immediately after cleaning. All damage of shop primer and contamination from storage and fabrication should be thoroughly cleaned prior to overcoating.

Preparation For Repair and Maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Remove all rust and loose material by abrasive blasting or power tool cleaning. Dust off residues. Touch up bare spots to full film thickness.

Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation. In confined spaces provide adequate ventilation during application and drying.

Technical Details
Components: Single Pack
Type: Zinc Phosphate
Finish: Flat
Stock Colours: 11480 Grey
Tintable: Yes, to most RAL or British Standard codes. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 30 g/L
Volume Solids: 41%
Suitable Substrates: For steel
Application Method: Airless Spray / Air Spray / Brush
Theoretical Coverage: 4.2 m2 per litre at 100 microns
Wet Film Thickness (WFT): 250 microns
Dry Film Thickness (DFT): 100 microns
Induction Time: -
Pot Life: -
Surface Dry: 45 minutes at 20°C
Overcoatable: See data sheet
Through Dry: 1.5 hours at 20°C
Cleaner / Thinner: HEMPEL'S THINNER 08080
Shelf Life: 5 years (25°C/77°F) from time of production
Packaging: Available in 5 and 20 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use