International Intergard 214

SKU
id18658
Part A and Part B: UN1263 (Class: 3, Pk Grp: III)
A two component epoxy sealer coat pigmented with aluminium flake.
Available in 5 Litres in Aluminium
£71.74 £59.78
In stock
Product Description

International Intergard 214 is a two component epoxy sealer coat pigmented with aluminium flake.

Best Uses

International Intergard 214 is formulated for the effective penetration and sealing of thermally sprayed aluminium coatings to eliminate porosity.

Intergard 214 can be overcoated with a wide range of products, including:

Application

All surfaces to be coated should be clean, dry and free from contamination. Prior to paint application all surfaces should be assessed and treated in accordance with ISO 8504:2000. Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning.

Thermally Sprayed Metal Coatings
Application of Intergard 214 should be undertaken within the recommended overcoating limits for metal spray. Normally, application of the sealer should take place within 4 hours of the final application of metal spray. The surface to be coated should be clean, dry and free from contamination before application of Intergard 214.

Apply using airless spray, conventional spray, brush or roller. Intergard 214 is designed to seal porosity in aluminium metal spray. When applying by brush, work
the sealer thoroughly into the surface of the aluminium metal spray. When application is by spray rather than by brush, careful inspection will be needed to ensure
thorough sealing of the aluminium metal spray. Any runs, sags or pooling on horizontal surfaces should be brushed out immediately.

Best results will be achieved at temperatures above 0°C (32°F).

Technical Details

Approvals

  • Highways Agency Approved - Item No. 159
  • London Underground New Works Approved N1 - APR No. 1928. Can be applied to below ground infrastructure
  • Network Rail Approved For New Works Systems - Protective Treatment Reference N1F - Certificate Ref: XN90/N1F-079
  • Network Rail Approved For New Works Systems - Protective Treatment Reference N1 - Certificate Ref: N1/112

Compatibility

Intergard 214 can be overcoated with a wide range of products, including:

Components: Two Part
Type: Epoxy Sealer Coat
Finish: -
Stock Colours: Aluminium
Tintable: No
VOC Content: 619.0g per Litre
Volume Solids: 30%
Suitable Substrates: For metal surfaces
Application Method: Brush, Roller, Conventional Spray or Airless Spray
Theoretical Coverage: 12 m2 per litre at 25 microns
Wet Film Thickness (WFT): 50 - 83 microns
Dry Film Thickness (DFT): 15 - 25 microns
Induction Time: -
Pot Life: -
Touch Dry: 30 minutes at 15°C
Overcoatable: After 3 hours at 15°C
Hard Dry: 3 hours at 15°C
Cleaner / Thinner: Thin if necessary with International GTA220. Clean up with International GTA822
Shelf Life: 12 months minimum at 25°C (77°F). Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.
Packaging: Available in 5 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use