Jotun Penguard Topcoat

SKU
id20770
Part A and B: UN1263 (Class: 3, Pk Grp: III)
A two component polyamide cured epoxy coating. To be used as topcoat in atmospheric environments.
Available in 5 and 20 Litres
From £68.26 £56.88
In stock
Only %1 left
Product Description

Jotun Penguard Topcoat is a two component polyamide cured epoxy coating. It has a glossy finish with fair gloss retention. To be used as topcoat in atmospheric environments.

Best Uses

Jotun Penguard Topcoat is formulated for marine use such as topside, deck and superstructure. It is also suitable for a wide range of industrial structures. Jotun Penguard Topcoat is designed to be used within a Jotun system as a topcoat.

Application

To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination. Optimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation.

Apply Jotun Penguard Topcoat with airless spray. Use a brush or roller for stripe coating and small areas. Care should be taken to reach the correct dry film thickness.

Depending on the actual exposure of the coating system, various primers and topcoats can be used in combination with this product. Some examples are shown below. Contact Promain's technical team for specific system recommendation.

  • Previous coat: zinc epoxy, zinc silicate, epoxy, epoxy mastic
  • Subsequent coat: epoxy, polyurethane
Technical Details

Approvals

  • Food, Compliant with USA, FDA Title 21, Part 175.300 for dry solids
  • When used as part of an approved scheme, this material has the following certification:
    Low Flame Spread in accordance with EU Directive for Marine Equipment. Approved in accordance with parts 5 and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with IMO 2010 FTP Code Ch. 8

Technical Info

Components: Two Part
Type: Polyamine Epoxy
Finish: Gloss
Stock Colours: Just tints
Tintable: Yes. Please note, bespoke tints are non refundable / exchangable.
VOC Content: 434.0g per Litre
Volume Solids: 50%
Suitable Substrates: To be used within a Jotun system as a topcoat.
Application Method: Airless Spray. Brush or Roller for small areas
Theoretical Coverage: 12.5 - 8.3 m2 per litre
Wet Film Thickness (WFT): 80 - 120 microns
Dry Film Thickness (DFT): 40 - 60 microns
Induction Time: -
Pot Life: 4 hours at 23°C
Touch Dry: 2.5 hours at 10°C
Overcoatable: After 7 hours at 10°C
Fully Cured: 7 days at 10°C
Cleaner / Thinner: Jotun Thinner No. 17
Shelf Life: Part a: 24 months, Part B: 48 months
Packaging: Available in 5 and 20 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.