Sika Sikafloor ProSeal 90

SKU
id21508
UN1866 (Class: 3, Pk Grp: III)
A solvent based, clear acrylic resin polymer solution used to cure, harden and seal fresh or hardened concrete.
Available in 25 Litres
£405.20 £337.67
In stock
Product Description

Sika Sikafloor ProSeal 90 is a solvent based, clear acrylic resin polymer solution used to cure, harden and seal fresh or hardened concrete floors.

Best Uses

Sikafloor® ProSeal-90 is used for optimum curing and sealing of fresh concrete floors and structures. ProSeal 90 is ideal as a curing compound in order to limit surface drying and cracking and provides curing and sealing for Sikafloor® dry shake hardeners.

Sikafloor® ProSeal-90 is suitable for exterior and interior application as an anti-dust treatment and improvement of the abrasion resistance of existing concrete surfaces.

  • Excellent moisture retention
  • Curing efficiency 90% (ASTM C-156)
  • Good adhesion to old and new concrete
  • Quick drying
  • Helps control dusting for both new and existing concrete floor surfaces
  • Effectively cures and seals concrete surfaces in a single, economic operation
  • Non yellowing
  • Easy application by spray or roller

Application

Fresh concrete:
Surface must be free of bleed water and of sufficient strength to withstand finishing operations. The concrete must be prepared by suitable power or manual floating / tamping techniques.

Hardened / old concrete:
The substrate must be prepared by suitable mechanical preparation techniques such as high-pressure water jetting or abrasive blast cleaning. All dust, loose and friable material must be completely removed from all surfaces before application of the product, preferably by brush and/or vacuum. If in doubt apply a test area first.

Sikafloor® ProSeal-90 is supplied ready for use. Stir thoroughly before use for a minimum of 2 minutes using a low speed electric stirrer (~300 rpm).

For fresh concrete, apply immediately after finishing techniques have been completed. Apply in a continuous even film by low-pressure spray unit. The suitability of spraying equipment must be confirmed by trials. Application also possible by brush or roller. To achieve the highest visual aesthetics and performance, a second coat is recommended. Wait for first coat to dry tack free before applying a second coat.

Technical Details

Approvals

  • Conforms to the requirements of ASTM C-309 for curing liquids type 1, ASTM C-156 for water retention, and ASTM D-4060 for improvement of abrasion resistance
  • Conforms to the requirements of EN 13813 SR – B 1.5 Test report from GEOCISA Ref. P-02/01463-A Rev. 1 dated August 7, 2002 Abrasion resistance according to UNE 48.250-92 (ASTM D-4060)
  • Test report from GEOCISA Ref. P-02/01463 dated June 7th, 2002 Water retention according to ASTM C-156 Epoxy textured roller and seal coat according to EN
    13813:2002, DoP 01 08 03 04 005 0 000008 1049 and provided with the CE-mark

Technical Info

Components: Single Pack
Type: Solvent Based
Finish:
Stock Colours: Clear
Tintable: No
VOC Content: 750 g/L
Volume Solids: 18%
Suitable Substrates: For fresh concrete
Application Method: Low Pressure High Volume Spray, Brush, Roller
Theoretical Coverage: 0.1 - 0.25 litre per m2 per coat. (4 - 10 m2 per litre per coat)
Wet Film Thickness (WFT): -
Dry Film Thickness (DFT): -
Induction Time: -
Pot Life: -
Foot Traffic: 3 hours at 20°C
Overcoatable: After 25 minutes minimum at 20°C
Fully Cured: 20 hours at 20°C
Cleaner / Thinner: Clean all tools and application equipment with Sika Thinner C immediately after use. Hardened / cured material can only be removed mechanically.
Shelf Life: 12 months from date of production, if stored properly in original, unopened and undamaged sealed containers, in dry conditions at temperatures between +5 °C and +25 °C.
Packaging: Available in 25 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use