£9.95 delivery on orders excluding certain products & postcodes *
Zinsser Allcoat Exterior Gloss (Solvent Based) is formulated for application to all exterior surfaces such as new or previously painted wood, metal, cladding, UPVC, stucco, brick, stone, cured concrete and more.
After removing existing mould and mildew, two coats of Zinsser Allcoat Exterior Gloss (Solvent Based) will ensure that any exterior looks bright and beautiful for years. Zinsser AllCoat® Exterior Gloss (Solvent Based) gives excellent resistance against cracking, blistering, chalking, and flaking. The silicon alkyd formula protects against rain and severe weather. Zinsser AllCoat® Exterior Gloss (Solvent Based) provides a long-lasting finish, is easy to apply and has exceptional colour retention. It dries even in low temperatures, so can be used all year round.
Surfaces should be clean, dry, sound and free of any contamination that may interfere with adhesion. Remove all loose or peeling paint and chalky residue. Sand edges of any remaining paint film until smooth. Ensure the moisture content of the substrate is a maximum of 12% prior to painting. Special precautions should be taken during surface preparation of pre-1960 paint surface as they may contain harmful lead. Avoid the inhalation of dust. Wear a suitable face mask if dry sanding.
New concrete, masonry and other related surfaces must be cured at least 30 days before painting. Remove all existing mould and mildew before painting. To effectively remove mould and mildew, use Blackfriar Fungicidal Wash. Timber at risk from decay or insect attack should be treated with Blackfriar Clear Wood Preservative.
Previously painted surfaces: Apply two coats of Zinsser AllCoat® Exterior Gloss (Solvent Based). Very hard or glossy surfaces should be abraded and degreased before applying 2 coats of Zinsser AllCoat® Exterior Gloss (Solvent Based).
New or Bare Surfaces: Concrete, masonry, brick, uPVC and metal (iron, steel, aluminium, galvanized) apply a suitable primer such as Zinsser Bulls Eye 123® to the suitably prepared surface before application of Zinsser AllCoat® Exterior Gloss (Solvent Based). Wood, apply a suitable primer such as Zinsser Cover Stain®. Before painting, fill all nail holes and gouges. Where necessary, spot prime knots and sap streaks with Zinsser B-I-N® Primer-Sealer. Cladding, Plastisol should be weathered and suitably prepared to ensure it is clean, dry and free from surface contamination such as mould, dirt etc prior to applying 2 coats of AllCoat® Exterior Gloss (Solvent Based).
Powder Coating: abrade and degrease thoroughly, ensure surface is clean, dry and free from surface contamination, prime with Zinsser Bulls Eye 123® prior to applying AllCoat® Exterior Gloss (Solvent Based).
APPLICATION – Shake or stir well before using. Apply with synthetic bristle brush, roller or sprayer. For airless spraying, use a .017” tip and high-medium (2000-2500 PSI) pressure. Apply when air and surface temperatures are between 5°-32°C and humidity is less than 85%. Avoid painting in direct sunlight and maintain a “wet edge” to avoid lapping. Do not apply if temperature is likely to fall below 5°C during the drying time.
Components: | Single Pack |
Type: | Solvent Based |
Finish: | Gloss |
Stock Colours: | Black and White |
Tintable: | Yes, to most RAL or British Standard codes. Please note, bespoke tints are non-refundable / exchangeable |
VOC Content: | 300 g/L |
Volume Solids: | 65% |
Suitable Substrates: | Ideal for new or previously painted wood, metal, cladding, UPVC, stucco, brick, stone, cured concrete and more |
Application Method: | Brush, Roller or Sprayer |
Theoretical Coverage: | 10 m2 per litre on non-porous substrates |
Wet Film Thickness (WFT): | - |
Dry Film Thickness (DFT): | - |
Induction Time: | - |
Pot Life: | - |
Touch Dry: | 4 hours at 20°C |
Overcoatable: | After 16 hours at 20°C |
Fully Cured: | 7 days at 20°C |
Cleaner / Thinner: | White spirits for cleaning equipment |
Shelf Life: | 2 years minimum in original unopened containers. |
Packaging: | Available in 2.5 Litres |