Centrecoat MMA Colour Coat is a two pack, extremely fast curing chemical resistant floor coating. Suitable for wet areas, cures at low temperatures, easy to clean and provides a hygienic finish.
Centrecoat MMA Colour Coat allows a rapid return to service as an abrasion and chemical resistant floor coating for warehouses, breweries, food production areas, abattoirs, kitchens or slaughterhouses. Also suitable as a tough, decorative finish coat for Centrecoat MMA Smooth Screed. Centrecoat MMA Colour Coat is ideal as a deck coating in many areas that have limited downtime.
- Colour Stable
- Very good chemical resistance
- Rapid curing minimises down times
- Suitable in wet areas
- Hygienic and easily cleaned
- Cures at low temperatures
- Hot water and fat resistant
The inherent slip resistance of Centrecoat MMA Colour Coat may be enhanced by the incorporation of a suitable anti-slip dressing aggregate.
Concrete surfaces shall be a minimum of 21 days old and/or the residual moisture content shall be below 6%. Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound, and existing paint finishes, etc. Blow holes and defective concrete shall be made good using a proprietary repair compound e.g. Centrecoat MMA Repair Mortar. Suitable mechanical treatment, such as vacuum grit blasting, is the preferred treatment prior to application as this ensures a mechanical ‘key’ which will optimise adhesion.
Steel surfaces shall be shot blasted or grit blasted to a nominal Sa 2.5 Swedish Standard. All dust shall be removed prior to coating application. A coat of Centrecoat MMA Steel Primer shall be applied as soon as practicable after blasting, in order to obviate the possible occurrence of ‘flash rusting’.
Concrete surfaces shall be primed with a coat of Centrecoat MMA Multi-Use Primer, applied by brush or roller, at a nominal rate of 0.3kg per m2. Long nap lambswool rollers are recommended for primer application. Allow primer to cure for a minimum of 40 minutes.
Steel surfaces shall be primed with Centrecoat MMA Steel Primer as soon as practicable after blasting.
Centrecoat MMA Colour Coat is supplied as a two pack material consisting of the BASE component, and the CATALYST component. Incorporate the CATALYST component into the BASE component under mechanical stirring, and mix for 1-2 minutes.
Apply Centrecoat MMA Colour Coat using short nap perlon, or smooth lambswool rollers at a nominal rate of 0.30kg/m2. Following a minimum of 1 hour apply a second coat at the same nominal rate. Should a slip resistant or skid resistant finish be required then broadcast an appropriate aggregate onto the first coat within
10 minutes of application. Following a minimum of 1 hour, sweep off excess aggregate and apply a second coat of Centrecoat MMA Colour Coat. May be applied at greater thicknesses should service conditions warrant it.
Clean tools with Centrecoat MMA Tool Cleaner immediately after use.
|Stock Colours:||Grey and Red|
|Tintable:||Yes, to most RAL or British Standard codes. Please note, bespoke tints are non refundable / exchangeable|
|Suitable Substrates:||For steel and concrete|
|Application Method:||Short nap perlon or smooth lambswool rollers|
|Theoretical Coverage:||A 5kg pack is sufficient to cover an area of 8.3m2 with the recommended two coat treatment, providing a minimum thickness of 500 microns|
|Wet Film Thickness (WFT):|
|Dry Film Thickness (DFT):||500 microns minimum|
|Pot Life:||15 - 20 minutes at 20°C|
|Light Foot Traffic:||1 hour at 20°C|
|Vehicular Traffic:||2 hours at 20°C|
|Full Chemical Resistance:||24 hours at 20°C|
|Cleaner / Thinner:||Clean tools with Centrecoat MMA Tool Cleaner immendiately after use|
|Shelf Life:||Store in dry conditions, out of direct sunlight, at temperatures between 10°C and 20°C. Adequate ventilation of the storage area should be provided. Keep container tightly closed when not in use Centrecoat MMA Colour Coat has a minimum shelf life of 6 months when stored in original, unopened containers in accordance with manufacturer’s instructions.|
|Packaging:||Available in 5 Kg|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.