Hempel Hempadur Fast Dry 17410

SKU
id21206
Part A: UN1263 (Class: 3, Pk Grp: III), Part B: UN3469 (Class: 3.8, Pk Grp: III)
A two-component epoxy paint, which combines high volume solids with a short drying time. Contains zinc phosphate for better corrosion protection.
Available in 20 Litres
From £165.08 £137.57
In stock
Only %1 left
Product Description

Hempel Hempadur Fast Dry 17410 is a two-component epoxy paint, which combines high volume solids with a short drying time. Contains zinc phosphate for better corrosion protection.

Best Uses

Hempel Hempadur Fast Dry 17410 is suitable for on-shore corrosion protection of new-build steel constructions where fast to handle and short overcoating times are required, such as steel for factory buildings, stadiums, exhibition halls, airports, power plants, refineries, chemical and petrochemical plants.

Application

Steel work: The steel surface shall be thoroughly prepared so that the coating achieves an even distribution at the specified nominal dry film thickness (please refer to the specifications). The final steel condition including welds and edges shall conform to preparation grade P2 (ISO 8501-3).

New steel: Abrasive blasting to Sa 2½, (ISO 8501-1:2007), with a surface profile equivalent to Rugotest No. 3 BN 10b, Keane-Tator Comparator 3.0 G/S or ISO Comparator, rough MEDIUM (G). For temporary protection, if required, use a suitable shop primer. All damage of shop primer and contamination from storage and fabrication should be thoroughly cleaned prior to final painting. For repair and touch-up use: HEMPADUR FAST DRY 17410.

Maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Remove all rust and loose material by wet or dry abrasive blasting or power tool cleaning. Feather edges to sound and intact areas. Dust off residues. Touch up to full film thickness. After wet abrasive blasting hose down the surface with fresh water and allow drying.

Apply using airless spray.

Technical Details
Components: Two Pack
Type: Zinc Phosphate
Finish: Semi Gloss
Stock Colours: 11320 Grey
Tintable: Yes, call to check. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 246 g/L
Volume Solids: 74%
Suitable Substrates: For onshore corrosion protection of new-build steel constructions
Application Method: Airless Spray
Theoretical Coverage: 7.4 m2 per litre
Wet Film Thickness (WFT): 100 - 125 microns
Dry Film Thickness (DFT): 70 - 125 microns
Induction Time: -
Pot Life: 1.5 hours at 20°C
Surface Dry: 45 minutes at 20°C
Overcoatable: See data sheet
Fully Cured: 7 days at 20°C
Cleaner / Thinner: Clean tools with HEMPEL'S TOOL CLEANER 99610. Thin with HEMPEL'S THINNER 08450 <5% depending on purpose
Shelf Life: 3 years for BASE and 1 year (25°C/77°F) for CURING AGENT from time of production.
Packaging: Available in 20 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use