Hempel Hempadur Quattro XO 17870

SKU
id19316
Part A: UN1263 (Class: 3, Pk Grp: III), Part B: UN3469 (Class 3,8, Pk Grp: III)
A universal pure epoxy and self-primed high performance coating system for atmospheric or in water service.
Available in 20 Litres
From £215.56 £179.63
In stock
Only %1 left
Product Description

Hempel Hempadur Quattro XO 17870 is a two-component, pure epoxy universal primer, which cures to a hard and tough coating with good resistance to abrasion and seawater.

The product is available with different levels of Aluminium and Fibre pigmentation to deliver tailor made optimized performance properties for different harsh service conditions.

Best Uses

Hempel Hempadur Quattro XO 17870 is best used as a universal pure epoxy and self-primed high performance coating system for atmospheric or in water service, including water ballast tanks to be coated according to IMO-PSPC requirements defined in the IMO Resolution MSC.215(82)). HEMPADUR QUATTRO XO 17870 is intended for all year application down to -10°C/14°F and for applications where fast recoating and handling is required.

Application

New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Abrasive blasting to minimum Sa 2½ (ISO 8501-1:2007) with a surface profile corresponding to Rugotest No. 3, N9a to N10, preferably BN9a to BN10, Keane-Tator Comparator, 2.0 G/S or ISO Comparator, Medium (G). Apply immediately after cleaning. All damage of shop primer and contamination from storage and fabrication should be thoroughly
cleaned prior to overcoating. For repair and touch-up use: HEMPADUR QUATTRO XO 17870.

Ballast tanks: For PSPC type approved coating, consult separate application instructions on the product data sheet.

Steel, maintenance: Remove oil and grease, etc. with suitable detergent. Remove salt and other contaminants by (high pressure) fresh water cleaning. Clean damaged areas thoroughly by power tool cleaning to St 3 (minor areas) or by abrasive blasting to min. Sa 2, preferably to Sa 2½. Improved surface preparation will improve the performance of the paint. As an alternative to dry cleaning, water jetting to sound, well adhering coat and/or to steel. Intact coat must appear with roughened surface after the water jetting. By water jetting to steel, cleanliness shall be Wa 2 - Wa 2½ (atmospheric exposure) / minimum Wa 2½ (immersion) (ISO 8501-4:2006). A flash-rust degree of maximum M (atmospheric exposure), preferably L (immersion) (ISO 8501-4:2006) is acceptable before application. Feather edges to sound and intact paint. Dust off residues. Touch up to full film thickness. On pit corroded surfaces, excessive amounts of salt residues may call for water jetting or wet abrasive blasting, alternatively dry abrasive blasting followed by high pressure fresh water hosing, drying, and finally, dry abrasive blasting again.

Other substrates: Contact Hempel or Promain Technical Department

Use only where application and curing can proceed at temperatures above: -10°C/14°F. Apply only on a dry and clean surface with a temperature min. 3°C/5°F above the dew point to avoid condensation. In confined spaces provide adequate ventilation during application and drying.

Technical Details

Certificates and Approvals

  • Tested for non-contamination of grain cargo at the Newcastle Occupational Health & Hygiene, Great Britain.
  • Norsok M-501 system no. 1 (Pre-Qualified)
  • Norsok M-501 system no. 2B
  • Norsok M-501 system no. 3B (Pre-Qualified)
  • Norsok M-501 system no. 3C

Features

  • Excellent anti corrosive and very good mechanical properties.
  • Available with Aluminium and Fibre pigmentation.
  • Short drying time.
  • Curing down to -10°C/14°F.

Technical Info

Components: Two Component
Type: Pure Epoxy
Finish: Semi-flat
Stock Colours: Grey 1648, Mid Grey 1148, Red 50630
Tintable: Yes, other shades according to assortment list. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 188 g/l [1.6 lbs/US gallon]
Volume Solids: 80 ±2%
Suitable Substrates: Steel
Application Method: Airless spray / Brush / Roller
Theoretical Coverage: 6.4 m2/l [256.6 sq.ft./US gallon] - 125 micron/5 mils
Wet Film Thickness (WFT): 150 micron [6 mils]
Dry Film Thickness (DFT): 125 micron [5 mils]
Induction Time: Consult the separate application instructions on the product data sheet
Pot Life: Airless Spray: 1 hour(s) 20°C/68°F, Brush: 1.5 hour(s) 20°C/68°F
Touch Dry: 3 approx. hour(s) 20°C/68°F
Overcoatable: After 1.5 hours minimum at 20°C - See Product Data Sheet for full information
Fully Cured: -
Cleaner / Thinner: Thinner: 08450 (5%), Clean tools with Hempel Tool Cleaner 99610
Shelf Life: 3 years for Base and 2 years (25°C/77°F) for Curing Agent from time of production.
Packaging: Available in 20 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use