International Intergard 5000
International Intergard 5000 is a light coloured, tar free, surface tolerant, universal primer with high volume solids (82%). Intergard 5000 is also tolerant of damp surfaces.
Best Uses
International Intergard 5000 is formulated as a one or two coat system which can be applied directly to mechanically prepared shop primed or grit blasted, hydroblasted or mechanically cleaned surfaces. For use at newbuilding, maintenance & repair or on board maintenance.
Application
All surfaces to be coated must be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil, grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 : solvent cleaning.
NEWBUILDING
Where necessary, remove weld spatter and smooth weld seams and sharp edges. Weld seams and areas of shop primer damage or breakdown should be blast cleaned to Sa2½ (ISO 8501-1:2007) or power tooled to Pt3 (JSRA SPSS:1984). Intact, approved, shop primers must be clean, dry and free from soluble salts and any other surface contaminants. Unapproved shop primers will require complete removal by blast cleaning to Sa2½ (ISO 8501-1:2007).
MAJOR REFURBISHMENT
Fresh water wash to remove all dirt and contamination. Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning. Abrasive blast clean to Sa2 (ISO 8501-1:2007) or hydroblast to International Paint hydroblasting standard HB2M/H (If abrasive blasting, the area should be fresh water washed prior to commencement).
REPAIR/OBM
Prepare areas of corrosion by mechanical cleaning to St3 (ISO 8501-1 : 2007) or hydroblast to International Paint Standard HB2M/H. Abrade surrounding intact area and feather the edges. When applying Intergard 5000 as a two coat scheme, Intergard 5000 Aluminium must always be applied as the first coat.
Intergard 5000 should not be used to maintain or overcoat one component coatings.
Apply using brush or roller for small areas. For main areas, use airless spray.
Can be overcoated by:
- Interbond 501
- Intercryl 700
- Interfine 629HS
- Intergard 1735
- Intergard 263
- Intergard 269
- Intergard 5000
- Intershield 851
- Interthane 990
Approvals
When used as part of an approved scheme, this material has the following certification:
- Fire Resistance - Surface Spread of Flame (WFR) - (BS476:Part 7)
- Fire Resistance - Fire Propagation (WFR-(BS476 Part 6))
- Fire Resistance - Smoke & Toxicity (Exova Warringtonfire)
- Food Contact - Carriage of Grain (NOHA)
Technical Info
| Components: | Two Pack |
| Type: | |
| Finish: | Semi Gloss |
| Stock Colours: | KBA501 - Aluminium |
| Tintable: | Yes, please call our Sales Team to check colours. Please note, bespoke tints are non refundable / exchangeable |
| VOC Content: | 2200 g/L |
| Volume Solids: | 82% |
| Suitable Substrates: | For metalwork |
| Application Method: | Brush, Roller or Airless Spray |
| Theoretical Coverage: | 5.47 m2 per litre at 150 microns dft, allow appropriate loss factors |
| Wet Film Thickness (WFT): | 183 - 427 microns/coat |
| Dry Film Thickness (DFT): | 150 - 350 microns per/coat |
| Induction Time: | - |
| Pot Life: | 2 hours at 5°C |
| Touch Dry: | 9 hours at 5°C |
| Overcoatable: | See table on product data sheet |
| Fully Cured: | |
| Cleaner / Thinner: | Clean equipment with International GTA220 |
| Shelf Life: | 12 months minimum at 25°C. Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition. |
| Packaging: | Available in 20 Litres |
