International Intergard 5000 is a light coloured, tar free, surface tolerant, universal primer with high volume solids (82%). Intergard 5000 is also tolerant of damp surfaces.
International Intergard 5000 is formulated as a one or two coat system which can be applied directly to mechanically prepared shop primed or grit blasted, hydroblasted or mechanically cleaned surfaces. For use at Newbuilding, Maintenance & Repair or On Board Maintenance.
All surfaces to be coated must be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil, grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 : solvent cleaning.
Where necessary, remove weld spatter and smooth weld seams and sharp edges. Weld seams and areas of shop primer damage or breakdown should be blast cleaned to Sa2½ (ISO 8501-1:2007) or power tooled to Pt3 (JSRA SPSS:1984). Intact, approved, shop primers must be clean, dry and free from soluble salts and any other surface contaminants. Unapproved shop primers will require complete removal by blast cleaning to Sa2½ (ISO 8501-1:2007).
Fresh water wash to remove all dirt and contamination. Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning. Abrasive blast clean to Sa2 (ISO 8501-1:2007) or hydroblast to International Paint hydroblasting standard HB2M/H (If abrasive blasting, the area should be fresh water washed prior to commencement).
Prepare areas of corrosion by mechanical cleaning to St3 (ISO 8501-1 : 2007) or hydroblast to International Paint Standard HB2M/H. Abrade surrounding intact area and feather the edges. When applying Intergard 5000 as a two coat scheme, Intergard 5000 Aluminium must always be applied as the first coat.
Intergard 5000 should not be used to maintain or overcoat one component coatings.
Apply using brush or roller for small areas. For main areas use airless spray.
Can be overcoated by:
When used as part of an approved scheme, this material has the following certification:
- Fire Resistance - Surface Spread of Flame (WFR) - (BS476:Part 7)
- Fire Resistance - Fire Propagation (WFR-(BS476 Part 6))
- Fire Resistance - Smoke & Toxicity (Exova Warringtonfire)
- Food Contact - Carriage of Grain (NOHA)
|Stock Colours:||KBA501 - Aluminium|
|Tintable:||Yes, please call our Sales Team to check colours. Please note, bespoke tints are non refundable / exchangeable|
|VOC Content:||2200 g/L|
|Suitable Substrates:||For metalwork|
|Application Method:||Brush, Roller or Airless Spray|
|Theoretical Coverage:||5.47 m2 per litre at 150 microns dft, allow appropriate loss factors|
|Wet Film Thickness (WFT):||183 - 427 microns/coat|
|Dry Film Thickness (DFT):||150 - 350 microns per/coat|
|Pot Life:||2 hours at 5°C|
|Touch Dry:||9 hours at 5°C|
|Overcoatable:||See table on product data sheet|
|Cleaner / Thinner:||Clean equipment with International GTA220|
|Shelf Life:||12 months minimum at 25°C. Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.|
|Packaging:||Available in 20 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.