Owatrol CIP Corrosive Inhibiting Primer is an anti-corrosive primer that penetrates metal and stops rust to steel structures, motor vehicles, civil engineering and marine equipment, railings, gates and nautical ballast tanks.
Owatrol CIP Corrosive Inhibiting Primer (formally RLS) is an anti-corrosive primer that possesses the penetrating properties associated with Owatrol Oil. Additionally Owatrol CIP has the added benefit that it may be overcoated with any coating, without the risk of it dissolving.
Owatrol CIP Corrosive Inhibiting Primer (Corrosive Inhibiting Primer) is an anti-corrosive primer that possesses the penetrating properties of Owatrol Oil with the added benefi t that it may be overcoated with any coating without the risk of it dissolving. Owatrol CIP Corrosive Inhibiting Primer stabilises the surface penetrating
deep into the substrate, driving out excess moisture and air to form a solid stable layer.
With Owatrol CIP Corrosive Inhibiting Primer, sand or shot-blasted surfaces do not require immediate priming; a light rust coating will not affect its performance or the final result.
- Interior and exterior use
- Horizontal and vertical surfaces
- New and rusted surfaces - Ferrous and non-ferrous metals
- Steel superstructures, motor vehicles
- Civil engineering and marine equipment
- Railings, gates
- Nautical ballast tanks
Surfaces must be clean, dry and free from oil, grease and other surface contaminants. Remove all mill scale; loose and flaking rust and old paint back to a sound surface and edge. Feather in any sharp edges. Surfaces exposed to chemicals (acids, alkalis or salt deposits) should be washed using copious amounts of water or steam cleaned. Severely contaminated surfaces should be cleaned using an appropriate solvent.
Stir well before and during use. Do not thin.
Prime with 1 coat of Owatrol CIP Corrosive Inhibiting Primer and allow to dry. For surfaces subject to aggressive climatic conditions apply 2 priming coats.
Clean, lightly rusted or new unpainted rusty steel:
Apply 2 coats of Owatrol CIP Corrosive Inhibiting Primer allowing drying time between coats.
Old severely rusted surfaces:
Apply 3 coats of Owatrol CIP Corrosive Inhibiting Primer allowing drying time between coats. OR Apply wet on wet applications of Owatrol Oil until rust is fully saturated and allow to dry 24 hours. Apply 2 coats of Owatrol CIP Corrosive Inhibiting Primer allowing drying time between coats.
Previously coated surfaces:
Spot prime all exposed metal with 2 coats of Owatrol CIP Corrosive Inhibiting Primer allowing drying time between coats Apply 3rd coat over entire area and allow to dry.
Surface and Environment
Owatrol CIP (Corrosive Inhibiting Primer) is suitable for use in interior or exterior environments on a variety of surfaces/substrates. Promain would recommend that it is idealyl suited for metal but Owatraol CIP can also be used on brickwork or wood.
Examples of uses for Owatrol CIP include: steel structures, motor vehicles, civil engineering and marine equipment, railings, gates and nautical ballast tanks.
- Owatrol CIP Corrosive Inhibiting Primer is a universal rust inhibiting primer for all paint types
- Does not dissolve or break down when hot solvent paints are applied over it
- Penetrates and stabilises the surface - increasing coating adhesion
- Pigmentation offers increased protection and perfect film-forming qualities
- Easy to use, no need for sanding or sandblasting
- Use on new or rusted surfaces - interior and exterior
- High temperature resistance up to 175°C
- Theoretical coverage is 15m2 per litre
- Heat resistant up to 175°C
|Type:||Solvent Based Alkyd Resin|
|Stock Colours:||Brick Red|
|VOC Content:||480 g/L|
|Suitable Substrates:||For ferrous and non ferrous metals|
|Application Method:||Brush, Roller or Airless Spray|
|Theoretical Coverage:||15 m2 per litre|
|Wet Film Thickness (WFT):|
|Dry Film Thickness (DFT):|
|Surface Dry:||24 hours at 20°C|
|Overcoatable:||Between 24 hours and 72 hours depending on finish at 20°C|
|Cleaner / Thinner:||Clean all tools and equipment with mineral sprits while still wet. If allowed to dry, remove with paint stripper.|
|Shelf Life:||2 years minimum in original unopened packaging|
|Packaging:||Available in 0.75, 2.5 and 20 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.