Bradite Polyurethane Floor Paint DP5

SKU
id18033
UN1263 (Class: 3, Pk Grp: III)
A high performance, hard wearing single pack flexible floor coating for use on interior concrete, wood or steel.
Available in 1 Litre, 2.5 Litres and 5 Litres
From £13.64 £11.37
In stock
Only %1 left
Product Description

Bradite Floor Paint is a top quality polyurethane resin based semi-gloss finish paint with excellent wash and wear resistance. For use on concrete and wooden floors subjected to light to medium traffic.

Best Uses

Bradite Floor Paint is best used on interior concrete, wood or steel floors requiring an economical, hard wearing, flexible floor coating with good chemical and excellent water resistance. It can also be used with Bradite Low Slip Additives LS30 to provide additional under foot traction.

Application

Substrates should be dust free and completely dry before coating. When painting concrete it is vital to ensure that the substrate is completely dry and free of laitance. Power floated, shiny or unpainted non-porous concrete floors should be thoroughly vacuum blast cleaned to a roughness profile of 30-50 microns, or acid etched using Bradite TA37, or primed using Bradite Floor Primer ES40. Please consult the product data sheet for more details. High pressure water cleaning should be utilised to remove all loose and flaking paint and contamination back to a sound substrate. Bradite TD39 industrial strength detergent should be used if necessary to remove all grease and oil. Intact areas of existing coatings should be roughened by abrasive manual or disc rubbing and feathered back to a sound coating edge. Cracks and pits should be filled using a suitable screed or mortar before painting.

Painting System

For application on concrete, wood or other absorbent substrates, the first coat should be thinned 15-20% with Bradite Thinner TW35 to allow penetration into the substrate.

1st coat Bradite Floor Paint DP5 (thinned)
2nd coat Bradite Floor Paint DP5
3rd coat Bradite Floor Paint DP5

For maintenance painting the 1st coat will be a touch up to bare areas only. While the floor will take light foot traffic after overnight drying, full cure may take 4 days at 20⁰C and should not be subject to heavy traffic for at least 48 hours. Please note that drying/curing times will vary depending on film thickness, temperature and relative humidity. Bradite Floor Paint DP5 is suitable for use in domestic and light commercial garages. In the first seven days after application, vehicles should be left outside to allow tyres to cool down (especially after long journeys) to help prevent hot tyre pick up. Spills of petrol and diesel should be cleaned up as soon as possible to reduce the danger of slip and to prevent discolouration of the floor paint. Brake fluid is highly aggressive and will attack most floor paints on contact – use drip/capture pans when working on brake systems to prevent permanent damage to the floor paint finish.

Technical Details
Components: Single Pack
Type: Polyurethane Alkyd
Finish: Semi-gloss (approx. 50%)
Stock Colours: Black, Light Grey, Dark Grey, Cardinal Red
Tintable: Yes. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 435 g/L
Volume Solids: 45%
Suitable Substrates: Internal steel, concrete, wood or other absorbent mineral substrates
Application Method: Brush, Roller, Airless Spray
Theoretical Coverage: 10 m2/L/coat
Wet Film Thickness (WFT): 100 microns/coat
Dry Film Thickness (DFT): 45 microns/coat
Induction Time: -
Pot Life: -
Surface Dry: 2 hours at 20°C
Overcoatable: After 16 hours minimum at 20°C
Fully Cured: 7 days at 20°C
Cleaner / Thinner: Bradite Thinner TW35
Shelf Life: 12 months minimum in original unopened containers
Packaging: Available in 5 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use