Centrecoat Grip Fast is the ideal solution for covering concrete, wood and metal floors with a slip resistant finish. Ideal for covering areas of warehouse floors to highlight walkways, safety areas or packing zones for easy identification. Centrecoat Grip Fast is also ideal for the infill of concrete parking bays such as electric car charging points, disabled bays and family parking.
Centrecoat Grip Fast is supplied in composite packs, each containing sufficient material to provide a slip-resistant epoxy coating system for 5 square metres of surface. Centrecoat Grip Fast is applied in a single coat operation which reduces the curing period of the system prior to trafficking. Apart from the excellent slip resistance characteristics, the coating system has very good abrasion and chemical resistant properties.
The slip resistant aggregate consists of graded aluminium oxide - Centrecoat Emery Aggregate.
Concrete should be a minimum of 21 days old and/or the residual moisture content shall be below 6%. Ensure that the concrete is clean and free from dust, laitance, grease, oil, curing compound, and existing paint finishes, etc.
Smooth concrete, or concrete with soft laitance, shall be mechanically treated by diamond grinding or grit blasting to provide a clean profiled surface. Should this not be practicable then acid etching, although less preferable, is also an option. Metal surfaces shall be power wire brushed to remove any rust and loose or flaking material. Grit blasting is recommended, where practical, for optimum performance. Coating application should be carried out immediately after preparation. Wood surfaces shall be sanded to a smooth finish, and all previous coating removed. Previously untreated wood shall be sealed with a coat of Centrecoat 525 WB Primer.
Pour the contents of the CURING AGENT container into the BASE container and thoroughly mix, preferably by mechanical means until a uniform colour and consistency is achieved.
Pour the mixed liquid components into a shallow roller tray. Apply by medium pile roller (not foam), to a measured 5 m². Immediately scatter the AGGREGATE uniformly onto the wet coating and ‘back roller’ to cover and encapsulate the aggregate.
Note: Although sufficient Aggregate is supplied to allow a full blinding, a lighter scatter may be made if required.
|Finish:||Textured (Via Aggregate)|
|Stock Colours:||Grey and Red|
|Tintable:||Yes, to most RAL or British Standard codes. Please note, bespoke tints are non refundable / exchangeable|
|Suitable Substrates:||For concrete, wood and metal floors|
|Application Method:||Medium Pile Roller (Broadcast Aggregate then back roll)|
|Theoretical Coverage:||5 m2 per pack|
|Wet Film Thickness (WFT):|
|Dry Film Thickness (DFT):|
|Pot Life:||30 minutes at 20°C|
|Tack Free:||3 hours at 20°C|
|Hard Dry:||6 hours at 20°C|
|Fully Cured:||7 days at 20°C|
|Cleaner / Thinner:||It is impracticable to clean rollers after use. Clean mixing equipment with Centrecoat MMA Tool Cleaner prior to curing of the coating.|
|Shelf Life:||Store in dry conditions at temperatures between 10°C and 25°C. Do not expose to freezing conditions.
Centrecoat Grip Fast has a minimum shelf life of 12 months when stored in original, unopened containers in accordance with manufacturer’s instructions.
|Packaging:||Available in 5m2 packs|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.