Remmers QP 100 Transparent Binder

SKU
id20637
Part A and B: UN3082 (Class: 9, Pk Grp: III)
A very fast reacting transparent binder for blind coatings that can full cure down to 0°C.
Available in 10 and 25 Kg
From £367.31 £306.09
In stock
Only %1 left
Product Description

Remmers QP 100 is a very fast reacting transparent binder for blind coatings that can full cure down to 0°C.

Best Uses

Remmers QP 100 is formulated as a base coat for blind coatings, as a transparent fixing layer for flake coatings or as a transparent top sealant. For professional users only.

  • High UV resistance
  • Full curing at temperatures form 0°C
  • Can be subjected to mechanical loads
  • Can be subjected to chemical loads

Application

The substrate must be load bearing, dimensionally stable, sound, free of loose constituents, dust, oil, grease, rubber tyre marks and other substances that could interfere with adhesion. Tensile strength of the surface of the substrate must be 1.5 N/mm² on average (smallest value of at least 1,0 N/mm²) and compressive strength at least 25 N/mm².

The use of suitable Remmers epoxy primers or scratch coats is mandatory. Compatible with Remmers MB 2K. Please refer to the current Technical Data Sheets of the single products as well as to the Remmers system recommendations for further details.

Epoxy Mortar
The material can be filled up to a mixing ratio of 1 : 10 by weight and distributed with a smoothing trowel and then smoothed. Application rate per mm of layer
thickness : approx. 0.2 kg/m² of binder and 2.0 kg/m² of Selectmix 0/10 Base coat for blind coatings. Apply the material filled up to 1 : 1 on the previously prepared
surface and distribute with a suitable toothed trowel / squeegee. The surface must immediately be worked over with a spiked roller. Immediately thereafter abundantly
apply a suitable blinding material on the still fresh surface. Application rate: approx. 0.75 kg/m² of binder and approx. 0.75 kg/m² of Selectmix 01/03

Fixation Of Flake Coverings
Before the application of the fixation layer the flakes (Remmers Sediment Flakes or Colorid) must always be ground with a black nylon pad. Pour the material generously on the surface. Distribute with suitable means, e.g. a rubber squeegee, and then roll over with an epoxy roller. Avoid the formation of pools. Application rate: 0.2 – 0.4 kg/m² of binder.

Top Sealant
Apply the material with a rubber squeegee and then roll over crosswise with a suitable epoxy roller. Application rate: 0,5 - 0,7 kg/m² of binder (depending on the blinding material)

Technical Details
Components: Two Part
Type: Solvent Based
Finish:
Stock Colours: Transparent
Tintable: No
VOC Content: 500.0g per Litre
Volume Solids:
Suitable Substrates: For floors
Application Method: Toothed trowel, toothed squeegee, rubber squeegee, epoxy roller, smoothing trowel.
Theoretical Coverage: Dependant on Application
Wet Film Thickness (WFT):
Dry Film Thickness (DFT):
Induction Time: 3 minutes at 20°C
Pot Life: 30 minutes at 20°C
Touch Dry: Dependant on Application
Overcoatable: Dependant on Application
Fully Cured: Dependant on Application
Cleaner / Thinner: Clean tools, equipment and splashed material immediately while fresh with Remmers V101 Thinner.
Shelf Life: At least 12 months in unopened and unmixed, original containers stored cool but frost-free.
Packaging: Available in 10 and 25 Kg

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use