Remmers Epoxy BS 3000 New Floor Paint
Remmers Epoxy BS3000 New, 2-component, water based epoxy resin floor paint with a wide range of applications. Suitable for garage floors, workshop or shop floors.
Best Uses
Remmers Epoxy BS 3000 SG New is used as a sealant in the Remmers Water Vapour Diffusion-Open System. Application examples include Production Rooms, Warehouses and Workshops, shops etc. Benefits include:
- Silk gloss or Matt finish
- Low odour
- Water vapour diffusion open
- Can be subjected to mechanical and chemical loads
- Can be subjected to vehicle traffic
- Can be made slip-resistant
- Physiologically safe
- Suitable for indoor areas
The substrate must be load-bearing, dimensionally stable, sound, free of loose material, dust, oil, grease, marks from rubber tyres or other substances that could interfere with adhesion. Tensile strength of the substrate must be1.5 N/mm² on average and compressive strength at least 25 N/mm². The substrate must also have sufficiently reacted and be load-bearing.
- Concrete max. 6 % by mass
- Cement screed max. 6 % by mass
Application
The substrate must be prepared by suitable means so that it meets the specifications given above, e.g. by steel shot blasting or diamond grinding. Fill broken out and missing areas flush with the surface using the Remmers PCC System or one of the Remmers EP Mortars. Then prime and, if necessary, level. Full application instructions can be found on the Technical Data Sheet.
Systems
- Remmers SS320 - Epoxy BS3000 Breathable Coating Systems (DFT = 350 - 400µ)
- Remmers SS320+ - Epoxy BS 3000 Breathable Systems (DFT = 300 - 350µ)
See technical tab for downloadable System Sheets.
Notes
All of the values and application rates given were determined under laboratory conditions (20 °C) with standard shades of colour. When worked at the building site, these values may deviate slightly. The coating system has a slightly textured surface which is typical for this type of system.
Technical Info
| Components: | Two pack system |
| Type: | Epoxy Resin Binder / Sealant |
| Finish: | Silk Gloss |
| Stock Colours: | RAL 7032, RAL 7001, RAL 7035, RAL 7030, RAL 7012 |
| Tintable: | Yes. Please note, bespoke tints are non refundable / exchangeable |
| VOC Content: | < 140 g/l (Both finishes) |
| Volume Solids: | 65% Silk Gloss, 68% Matt |
| Suitable Substrates: | Suitable for indoor areas |
| Application Method: | Brush or Roller |
| Theoretical Coverage: |
Sealant: approx. 0.15 - 0.20 kg/m² per working operation. Top Sealant: approx. 0.60-0.80 kg/m² binder in two coats |
| Wet Film Thickness (WFT): | - |
| Dry Film Thickness (DFT): | - |
| Working Temperature: | Minimum 8°C and Maximum 30°C - The substrate must also be at least 3°C above the dew point |
| Pot Life: | 30 minutes at 20°C (Both finishes) |
| Waiting Time: |
Minimum of 16 hours and maximum of 48 hours at 20°C (Silk Gloss) Minimum of 8 hours and maximum of 48 hours at 20°C (Matt) |
| Drying Time: | Foot Traffic after 1 day, Mechanically loadable after 3 days at 20°C (Both finishes) |
| Fully Cured: | Full loading capacity after 7 days at 20°C (Both finishes) |
| Cleaner / Thinner: | - |
| Shelf Life: | At least 9 months unopened |
| Packaging: | Available in 1 Kg, 5 Kg, 10 Kg and 25 Kg |
RELATED PRODUCTS
