Remmers Betofix Filler

SKU
id17604
Non Hazardous
PCC fine filler for structural repair of concrete structures.
Available in 5 Kg and 25 Kg paper bags
From £52.10 £43.42
In stock
Only %1 left
Product Description

Remmers Betofix Filler is a factory mixed, mineral, dry mortar that is ready to use after mixing with water. The very smooth material hardens with little shrinkage and crack-free.

Best Uses

Remmers Betofix Filler is a PCC fine filler best used for structural repair of concrete structures. Polymer additives improve adhesion of the mortar, making it especially suitable for vertical and over-head work. The hardened mortar is resistant to water, weather, frost and frost/de-icing salt.

  • Scratch coat and levelling filler for use indoors and outdoors
  • Partial and full surface levelling of concrete surfaces
  • Coating prefab elements, masonry work and mineral surfaces
  • Repairing holes, cracks, voids, missing and broken out areas
  • Can be used indoors and outdoors, in wet and under water areas

Application

At the time of application the substrate must be matt damp, sound and load-bearing. Remove loose material that could interfere with adhesion and cement grout e.g. by blasting. The substrate must also be sufficiently rough. The pull-off strength of the substrate must correspond to the relevant technical rules. The pre-wet substrate should be still slightly absorbent.

Pour approx. 3.8 l of water into a clean container (mortar tub), then add 25 kg Betofix Filler. Mix thoroughly with a mixer/positive mixer for approx. 2 minutes until homogeneous and until the proper consistence for working has been achieved. If necessary, a little more water may be added. Mixing by hand as well as the preparation of partial amounts is not permissible. To achieve the best possible adhesion between the concrete and filler, a scratch coat should be applied to the matt amp substrate first. The filler can be applied in a single layer from 1 - 6 mm thick and in broken out areas up to 10 mm.

Initially set mortar cannot be made workable again by adding water or fresh mortar. Do not use if the temperature of the air, substrate and building material is below +5 °C or above +30 °C. Low temperatures lengthen, high temperatures reduce working and setting time.

Protect the fresh mortar surface for at least 4 days from weather influences such as sun, wind, rain, drafts and frost to and from too fast dehydration.

Technical Details

Notes

  • Reaction to fire: Class A1
  • May contain traces of pyrite (iron sulphide).
  • Low in chromates in accordance with Directive 2003/53/CE

Technical info

Components: Single Pack
Type: Dry Mortar
Finish: -
Stock Colours: Grey
Tintable: No
VOC Content: -
Volume Solids: -
Suitable Substrates: Concrete both indoor and outdoors
Application Method: Filling Knife and Trowel
Theoretical Coverage: Approx. 1.75 kg/m²/mm layer or approx. 1.75 kg/dm³
Wet Film Thickness (WFT): -
Dry Film Thickness (DFT): -
Induction Time: -
Working Time Approximately 60 minutes
Touch Dry: -
Overcoatable: -
Fully Cured: After 4 days at 20°C
Cleaner / Thinner: Clean tools with water before the mortar sets
Shelf Life: 9 years unopened
Packaging: Available in 5 Kg and 25 Kg

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use