£9.95 delivery on orders excluding certain products & postcodes *
Remmers Epoxy BS 2000 - New
SKU
ID17625
Part A: Non Hazardous, Part B: UN3082 (Class: 9, Pk Grp: III)
Water-based primer paint for use as a bonding layer on old coatings and ceramic coverings.
Available in 5, 10 and 25 Kg
From
£87.60
£73.00
In stock
Only %1 left
Product Description
Remmers Epoxy BS 2000 is a pigmented primer on a water emulsifiable epoxy resin base with a wide application spectrum. It is for use by Professional Users.
Best Uses
Epoxy BS-2000 is best used as a primer in Remmers WDD systems as well as for other cementitious, ceramic substrates and for old epoxy resin coatings (set up a trial area). Primer in DIBt approved systems for common rooms (general building inspectorate approval Z-156.605-1414)
Application
Preparation - Prepare the substrate by suitable means, e.g. steel shot blasting, so that it meets the required specifications as shown on the Technical Data Sheet. Broken out or missing areas in the substrate should be filled flush with the surface using Remmers PCC systems or Remmers EP mortars.
Temperature of material, surroundings and substrate: min. +8 °C - max. +30 °C. During the curing process, the applied material should be protected from moisture which could impair the surface and impair the adhesion. Relative humidity should not exceed 80%. The temperature of the substrate must be at least 3 °C above the dew point temperature during application and curing. Good ventilation must be ensured so that water can be released into the air.
Priming -The mixed resin is generously applied to the surface. Distribute with a suitable tool, e.g. rubber blade, and work into the substrate with an epoxy roller so that pores in the surface of the substrate are completely filled. It may be necessary to apply several layers.
Add the entire quantity of the hardener (component B) to the basic compound (component A). Mix thoroughly with a slow-speed electric mixer (approx. 300 - 400 rpm).
Pour the mixture into a separate container and mix again thoroughly. Mix for at least 3 minutes. Insufficient mixing is indicated by streaks forming. On highly absorbent substrates the product can be diluted with water up to 10 % by mass. Mixing ratio (A : B) 85 : 15 parts per weight.
As soon as the mixture is ready to use, apply it in full to the prepared surface and spread it using suitable tools.
Technical Details
Systems
- Remmers SS320 - Epoxy BS3000 Breathable Coating Systems (DFT = 350 - 400µ)
- Remmers SS320+ - Epoxy BS3000 Breathable Systems (DFT = 300 - 350µ)
- Remmers SS320M - Epoxy BS3000 M Breathable Coating Systems (DFT = 350 - 400µ)
See technical tab for downloadable System Sheets.
Notes
The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion. The tensile strength of the surface of the substrate must be at least 1.5 N/mm² on average (smallest individual value of at least 1.0 N/mm²), and the compressive strength must be at least 25 N/mm². Substrates must have reached their moisture balance and must also be protected against moisture penetration from the reverse side, including during utilisation. See Technical Data Sheet for full information.
Technical Info
| Components: | Two Componet Set |
| Type: | Water based Primer |
| Finish: | - |
| Stock Colours: | RAL 7012, RAL 7030, RAL 7035, RAL 7001, RAL 7032 |
| Tintable: | No |
| VOC Content: | < 140 g/l |
| Volume Solids: | 55% |
| Suitable Substrates: | Concrete, Cement Screed |
| Application Method: | Brush or roller |
| Theoretical Coverage: | Can vary depending on substrate - See Technical Data Sheet |
| Wet Film Thickness (WFT): | - |
| Dry Film Thickness (DFT): | - |
| Working Time: | Max 60 minutes |
| Pot Life: | 60 Minutes |
| Drying Time: | Foot Traffic after 1 day, Mechanical Loads after 3days |
| Overcoatable: | - |
| Fully Cured: | Full Loading Capacity after 7 days |
| Cleaner / Thinner: | Clean tools with water while still fresh |
| Shelf Life: | 9 months unopened |
| Packaging: | Available in 5 Kg and 10 Kg |
Related Products
Remmers Epoxy MT 100
Special primer for matt damp substrates based on a transparent epoxy resin.
From
£287.24
£239.37
Remmers Colorid Collection Flakes
A blend of PVC flakes designed to be broadcast over Remmers synthetic floor coatings.
From
£238.43
£198.69
Centrecoat Clearcoat
A 2 pack rapid curing and versatile chemical resistant sealer / clear coating.
From
£38.23
£31.86
Remmers Epoxy BS 3000 SG New Floor Paint
High quality, silk gloss, water based, epoxy resin floor paint.
From
£115.43
£96.19
Remmers QP 100 Transparent Binder
A very fast reacting transparent binder for blind coatings that can full cure down to 0°C.
From
£403.20
£336.00
Centrecoat Armourcoat WB 2-80
A 2 pack water based epoxy floor paint for concrete and polymer modified cementitious screeds. Category FeRFA Type 1 & 2.
From
£72.00
£60.00
Remmers Add 250 Polymer Granules
Polymer granules intended for use with Remmers HB Flooring products to produce slip-resistant sealants.
From
£39.00
£32.50
RODO Paddle Mixer
Ideal for use as an attachment to a drill to enable the thorough mixing of paints and coatings.
From
£9.24
£7.70