Owatrol Teak Olje is ideal for the deep protection of hardwoods such as teak giving a rich, warm, matt finish to any treated wood surface. Teak-Olje replaces the natural oils lost by exterior wood in the weathering process and will not blacken when exposed to UV rays making it ideal for garden furniture. Also ideal for interior woods. Suitable for both horizontal and vertical use.
Surfaces must be clean, dry and free of dirt, grease, grime, mildew and previous coatings. Treat mildew with a 50/50 bleach/water solution. Scrub solution on to surface and allow to stand for 10-15 minutes, rinse thoroughly. After stripping and cleaning, allow wood to dry 2-3 good drying days or until it has reached a moisture
content of 18 % or less before applying finish.
Owatrol Teak Olje may only be applied to bare wood surfaces or weathered wood surfaces previously finished with Owatrol Teak Olje. ALL other finishes must be completely and thoroughly removed. If necessary sand surface after cleaning and/or stripping (100 grit paper).
Preparation For New Wood:
Preparation For Weathered Wood Surfaces (untreated):
Clean weathered wood with Owatrol Net-Trol, to remove the loose wood fibres, dirt and other surface contaminants. If wood is severely contaminated, clean with Owatrol Aquanett and neutralise with Owatrol Net-Trol.
Preparation For Previously Oiled Surfaces:
All other oils or sealers must be completely and thoroughly removed with Owatrol Aquanett and stripped surfaces neutralised with Owatrol Net-Trol, before applying Owatrol Teak Olje.
Preparation For Previously Coated Surfaces (Paint, Stain, Varnish, Waterproofers...):
All previous coatings must be completely and thoroughly removed with Owatrol Dilunett and the stripped surface neutralised with Owatrol Net-Trol before applying Owatrol Teak Olje.
Preparation Of Other finishes: Contact our technical department for additional information and advice.
Note: Hardwoods inc’ exotic hardwoods and woods rich in tannins i.e. Teak, Iroko, Merbau, Oak... may darken with Owatrol Aquanett and Owatrol Dilunett, neutralising with Owatrol Net-Trol immediately after rinsing will lighten and restore the woods colour.
Apply 2 even applications of Owatrol Teak Olje wet on wet. Apply 1st application of Owatrol Teak Olje and allow to penetrate, normally 15-20 minutes. Apply 2nd application and allow to penetrate. If required repeat this procedure until the wood is saturated i.e. will accept no more material. Do not allow Owatrol Teak Olje to become touch dry or dry between applications. Brush out or wipe up any excess Owatrol Teak Olje with a lint free cloth 15-20 minutes after last application to avoid shiny spots. Allow to dry.
Note: Owatrol Teak Olje is not a surface coating, its place is in the wood and not on the surface. Owatrol Teak Olje protects by penetrating the wood, providing a rich matt finish.
|VOC Content:||700 g/L|
|Suitable Substrates:||For teak and exotic hardwoods in internal and external settings|
|Application Method:||Brush, Roller, Airless Spray or Garden Sprayer|
|Theoretical Coverage:||Initial: 5 to 7 m2 per litre per 2 applications.
Maintenance: 10 to 14 m2 per litre per application.
Actual coverage will vary depending on application method, type, texture, age and porosity of the wood.
|Wet Film Thickness (WFT):||-|
|Dry Film Thickness (DFT):||-|
|Touch Dry:||24 hours at 20°C|
|Cleaner / Thinner:||Clean all tools and equipment with white spirits while still wet. If allowed to dry, remove with paint stripper.
NOTE: Any rags, steel wool etc soaked in Owatrol Teak-Olje may spontaneously catch fire if improperly discarded. Rags, steel wool etc must be saturated with water after use or placed in a sealed, water filled metal container, before disposing with household waste.
|Shelf Life:||2 years in original unopened packaging.|
|Packaging:||Available in 2.5 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.