Sika Sikafloor 2510W

A2 pack, water-based, coloured epoxy resin floor coating with low emissions and low maintenance requirements.

Available in 20 Kg

* These colours are for guidance only. Variations between output devices can misrepresent the appearance of an actual colour. Also, we strongly advise that you order your complete paint requirements simultaneously to ensure a uniform batch colour.

2. Size

3. Select a Qty

As low as:

£576.36

Inc VAT £691.63

PRODUCT DETAILS

Please note, this is a made to order product with a 7 - 10 leadtime for delivery.

Sika Sikafloor 2510 W is a two-part, water-based, coloured epoxy resin floor coating with low emissions and low maintenance requirements.

Best Uses

Sika Sikafloor 2510W is used as a primer or scratch coat, smooth or textured roller coat, self-smoothing wearing layer, or a seal coat within various Sika Flooring Systems.

Suitable for use on concrete and cementitious substrates. May only be used for interior applications.

Low VOC emissions
Good resistance to abrasion
Good resistance to specific chemicals
Good mechanical resistance
Low odour
Easy application
Low maintenance

Sika Sikafloor 2510 W may only be used by experienced professionals.

Application

Construction joints and existing static surface cracks in substrate require pre-treating before full layer application. Use Sika Sikadur or Sika Sikafloor resins.

PREPARATION
Cementitious substrates must be structurally sound and of sufficient compressive strength (minimum 25 N/mm2) with a minimum tensile strength of 1.5 N/mm. Substrates must be clean, dry and free of contaminants such as dirt, oil, grease, coatings, laitance, surface
treatments and loose friable material.

Surface defects due to voids in the substrate - Voids and blow holes in the substrate will weaken the surface and damage the covering Product if not repaired during the preparation process. Fully expose blow holes and voids during surface preparation to identify the required repairs. Remove weak cementitious substrates. Prepare cementitious substrates mechanically using abrasive blast cleaning, abrasive planing or scarifying equipment to remove cement laitance. Before applying thin layer resins, remove high spots by grinding. Use industrial vacuuming equipment to remove all dust, loose and friable material from the application surface before applying the Product. Use products from the Sikafloor, Sikadur and Sikagard
range of materials to level the surface or fill cracks, blow holes and voids.

APPLICATION
See datasheet for all recommendations and warnings to ensure coating is to be as expected.

PRIMER OR ROLLER COAT APPLICATION
Pour the mixed Product onto the substrate. Note the consumption on the product datasheet..

Apply the Product evenly over the surface with a short pile roller or a squeegee
Back-roll the surface in two directions at right angles with a fleece roller. Note: Maintain a 'wet edge' during application to achieve a seamless finish

SCRATCH COAT APPLICATION
Pour the mixed Product onto the substrate. Note the consumption on the product datasheet.

Apply the Product evenly over the surface with a trowel or a squeegee.

TEXTURED COATING APPLICATION
Pour the mixed Product onto the substrate. Note the consumption on the product datasheet.

Apply the Product in two directions at right angles with a textured roller. Note: Maintain a 'wet edge' during application to achieve a seamless finish

SELF SMOOTHING LAYER APPLICATION
Pour the mixed Product onto the substrate. Note the consumption on the product datasheet.

Apply the Product evenly over the surface with a serrated / notched trowel
To achieve a smooth finish, smooth the surface with the flat side of a trowel
Back roll the surface in two directions at right angles with a steel spike roller

SEAL COAT FOR BROADCAST SURFACES
Pour the mixed Product onto the substrate. Note the consumption on the product datasheet.

Spread the Product evenly over the surface with a squeegee
Back-roll the surface in two directions at right angles with a fleece roller. Note: Maintain a 'wet edge' during application to achieve a seamless finish.

TECHNICAL

Approvals and Certifications

Environmental Product Declaration (EPD) in accordance with EN 15804. EPD independently verified by Institut für Bauen und Umwelt e.V. (IBU)
CE marking and declaration of performance based on EN 13813:2002 Screed material and floor screeds - Screed material - Properties and requirements - Synthetic resin screed material
CE marking and declaration of performance based on EN 1504-2:2004 Products and systems for the protection
and repair of concrete structures - Surface protection systems for concrete - Coating

Technical Info

Components:	Two Pack
Type:	Water Based Epoxy
Finish:	Semi Gloss
Stock Colours:	See colour card
Tintable:	Yes, to either opaque or translucent shades in most RAL or British Standard codes. Please note, bespoke tints are non refundable / exchangeable
VOC Content:
Volume Solids:	60%
Suitable Substrates:	Concrete and cementitious substrates
Application Method:	Trowel, Short Pile Nylon Roller, Squeegee
Theoretical Coverage:	Primer Sikafloor®-2510 W + 10 % water 0.15 to 0.2 kg/m² Scratch Coat Sikafloor®-2510 W + 4 % Sika Extender T 0.3 kg/m² Smooth Roller Coat Sikafloor®-2510 W 0.15 to 0.2 kg/m² Textured Roller Coat Sikafloor®-2510 W + 2 % Sika Extender T + 3 % quartz sand 0.3 to 0.8mm 1 to 2 × 0.2 to 0.3 kg/m² per layer Self-smoothing Layer Sikafloor®-2510 W filled up to 1 : 1 with quartz sand 0.1 to 0.3 mm 3.8 kg/m² Seal Coat Sikafloor®-2510 W 0.7 to 0.9 kg/m² applied in 2 layers
Wet Film Thickness (WFT):
Dry Film Thickness (DFT):
Induction Time:	-
Pot Life:	90 minutes at 20°C
Foot Traffic Ready:	20 hours at 20°C
Overcoatable:
Fully Cured:	5 days at 20°C
Cleaner / Thinner:	Clean all tools and application equipment with water immediately after use. Hardened material can only be removed mechanically.
Shelf Life:	12 months from date of production
Packaging:	Available in 20 Kg