Teknos Nordica Classic

Non Hazardous
A semi-matt, acrylate based, waterborne paint for wooden surfaces outdoors.
Available in 2.7, 9 and 18 Litres
From £33.58 £27.98
In stock
Only %1 left
Product Description

Teknos Nordica Classic is a semi-matt, acrylate based, waterborne paint for wooden surfaces outdoors.

Best Uses

Teknos Nordica Classic is an environmentally friendly facade paint that provides a hard surface that is dirt-repellent. Teknos Nordica Classic retains its appearance and colour for a very long time.

Teknos Nordica Classic is suitable for use and application to surfaces previously painted wooden surfaces with acrylate paints e.g. exterior walls, facia boards and weather boards. May also be used for maintenance painting on most old oil and alkyd paints, if the surfaces are in good condition. Also suitable for maintenance painting of previously with alkyd or acrylate paints painted facade sheetings.

However, this product is not suitable for log surfaces. For log surfaces we would recommend Teknos Woodex Aqua Classic wood stain.


Treat the surface as soon as possible. At least the impregnation and priming would be best done in the summer of construction. Remove from the surface all loose matter, dirt, dust and mildew. If needed, use Teknos Rensa Facade cleaner. Apply a coat of clear wood preservative from the Teknos Woodex series. Allow to dry for one day. Prime wooden surfaces with Teknos Nordica Primer and allow the surfaces to dry for 1 - 3 days depending on the weather. Wash the metal parts with Teknos Teknosolv 1621 (solvent naphtha) and prime with Teknos Ferrex Aqua.

Replace deteriorated wooden parts with new ones. Remove loose matter, dirt and dust. Remove the deteriorated paint coats entirely. Note, that the adhesion of an old thick paint layer to the substrate may have been weakened, therefore the paint should be removed although the paint film looks intact. The old paint layer is removed primarily by scraping or wire brushing and possibly by heating the surface with infra-red heater designed for that purpose. Secondarily paint remover or blasting can be used.

The surface of old oil paint coats may be in poor condition: heavily chalked, dusty and brittle. These types of surfaces must be carefully cleaned so, that the new paint adhered properly to the substrate. Some traditional paint types, such as red ochre paint and paraffin oil paint, produce such a brittle and dusty surface, that they can't be maintenance painted with Teknos Nordica Classic. If there is doubt about the adhesion, it must be ensured by test painting. Wash surfaces with Teknos Rensa Facade cleaner and rinse thoroughly.

See product data sheet for more details.

Stir the paint well and apply by paint brush or spray once or twice. If the paint is applied by spray, the surface is to be finished by a brush to ensure the adhesion.

Technical Details
Components: Single Pack
Type: Water borne acrylate
Finish: Semi Matt
Stock Colours: Pure White
Tintable: Yes, to most RAL or British Standard codes. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 130 g/L
Volume Solids: 37%
Suitable Substrates: Exterior wood verticals
Application Method: Brush or Spray
Theoretical Coverage: Planed timber: 8 - 10 m2 per litre
Sawn timber: 5 - 8 m2 per litre
Facade sheetings: 8 - 10 m2 per litre
Wet Film Thickness (WFT):
Dry Film Thickness (DFT):
Induction Time: -
Pot Life: -
Surface Dry: 1 hour at 23°C
Overcoatable: After 2 - 4 hours at 23°C
Fully Cured:
Cleaner / Thinner: Water
Shelf Life: See container
Packaging: Available in 2.7, 9 and 18 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use