Teknos TeknosPro 10

SKU
id20358
Non Hazardous
For dry indoor spaces such as interior walls and ceilings.
Available in 2.7 and 9 Litres. Tintable to RAL and BS Colours as well Teknos inhouse colours
From £35.40 £29.50
In stock
Only %1 left
Product Description

Teknos TeknosPro 10 is an alkyd-reinforced acrylate dispersion paint for dry indoor spaces with a matt low side sheen finish.

Best Uses

TeknosPro 10 is best used on interior walls and ceilings, e.g. in apartments and offices. It is easy to apply and gives a smooth, matt surface with attractive appearance. It can be applied to concrete, plaster, filler, brick and to various building boards. It can also be used for repainting old alkyd and dispersion paint coats.

Application

Clean new surfaces from dust and dirt. Wash previously painted surfaces with Rensa Super paint cleaner. Sand hard or gloss surfaces and remove the dust. Remove all of the old paint from the surfaces which have been painted with glue paint or lime wash. Spray filler ceilings, which are not waterproof, are recommended to be primed with solvent borne primer e.g. Futura 3 Adhesion primer.

For smoothing of irregularities in the surface choose a suitable stopper from the TeknosPro series. The dried stopper is sanded down and the dust removed. Prime concrete, plaster, stopper, brick and building board surfaces with Teknospro Pohja Primer. Steel surfaces are primed with Ferrex Aqua Anticorrosive paint.

Before use stir the paint thoroughly. The paint is thinned with water when needed. Apply once or twice by brush, roller or spray. Suitable nozzle for airless spray is 0.017 - 0.021".

The surface to be painted has to be dry. During the application and drying period the temperature of the ambient air, the surface and the paint shall be above +5°C and the relative air humidity below 80%. Good ventilation during the application and drying period quickens the drying process.

Maintenance instructions: The final forming of the paint film takes approximately 4 weeks under normal circumstances and after that the ultimate durability and hardness is reached. Before this, the painted surface must be treated with care. The painted surface can be cleaned by wiping with a neutral (pH 6 - 8) detergent. For very dirty surfaces alkalescent (pH 8 - 10) detergents can be used. Detergent and dirt are removed by wiping and/or rinsing the surface with clean water. Use a cleaning cloth, soft sponge or similar for cleaning. Avoid coarse brushing or heavy abrasion. Follow the dilution and other instructions of the detergent producer when using detergents.

Technical Details

Certificates & Approvals

  • Classified in Emission Classification of building materials to Group M1

Technical info

Components: Single Pack
Type: Water-borne
Finish: Matt
Stock Colours: Off-White T1327
Tintable: Yes, to the Teknos Interior Colour Cards and RAL, BS Shades. Please note, bespoke tints are non refundable / exchangeable
VOC Content: 30 g/l
Volume Solids: 38%
Suitable Substrates: Concrete, plaster, filler, brick and to various building boards
Application Method: Brush, Roller or Airless Spray (Suitable nozzle for airless spray is 0.017 - 0.021").
Theoretical Coverage: Previously Painted Surface: 10-12 m2/l, Filler & Wood Fibre Board: 7-10 m2/l, Concrete & Plastered Surface: 4-7 m2/l
Wet Film Thickness (WFT): -
Dry Film Thickness (DFT): -
Induction Time: -
Pot Life: -
Drying time, dust free: 30 minutes at 23°C
Overcoatable: After 1 hour at 23°C
Fully Cured: -
Cleaner / Thinner: Water
Storage: Must not freeze
Packaging: Available in 2.7 and 9 Litres

The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.

Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.

Recommended products to use