Hempel Hempadur Multi-Strength 45540 is a two component pure epoxy paint which cures to an abrasion and corrosion resistant coating. Applicable by standard heavy duty airless spray equipment.
Hempel Hempadur Multi-Strength 45540 is formulated as a maintenance and repair primer in Hempadur systems in severely corrosive environment. Formulated as a self-primed, high build coating primarily for maintenance of e.g. structural steel, tidal zones, jetty pillings and decks. Well suited for application under humid conditions and for early water exposure.
Preparation For New Steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Abrasive blasting to minimum Sa 2½ (ISO 8501-1: 2007) with a surface profile corresponding to Rugotest No. 3, N9a to N10, preferably BN9a to BN10,
Keane-Tator Comparator, 2.0 G/S or ISO Comparator, Medium (G).
Preparation For Repair and Maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Remove all rust and loose material by wet or dry abrasive blasting or power tool cleaning.As an alternative to dry cleaning, wet abrasive
blasting or water jetting to min. Wa 2½ (ISO 8501-4:2006) (or according to specification), may be used. A flash-rust degree of maximum L (ISO 8501-4:2006) is acceptable before application. Feather edges to sound and intact areas. After wet abrasive blasting hose down the surface with fresh water and allow drying. Touch up bare spots with: specified HEMPADUR paint.
Use only where application and curing can proceed at temperatures above: 5°C/41°F. The temperature of the paint itself should be above: 15°C/59°F. Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation. In confined spaces provide adequate ventilation during application and drying.
Hempel Hempadur 15590 may be used as a blast primer.
|Stock Colours:||17700 Mid Grey, 19990 Black, RAL 9010, 10170|
|Tintable:||Yes, upon request. Please note, bespoke tints are non refundable / exchangeable|
|VOC Content:||176 g/L|
|Suitable Substrates:||For maintenance of e.g. structural steel, tidal zones, jetty pillings and decks|
|Application Method:||Airless Spray / Brush / Roller|
|Theoretical Coverage:||2.4 m2 per litre at 350 microns|
|Wet Film Thickness (WFT):||425 microns|
|Dry Film Thickness (DFT):||350 microns|
|Pot Life:||1.5 hours at 20°C|
|Surface Dry:||3.5 hours at 20°C|
|Overcoatable:||See data sheet|
|Fully Cured:||7 days at 20°C|
|Cleaner / Thinner:||Hempel Thinner 08450|
|Shelf Life:||1 year for BASE and 3 years (25°C/77°F) for CURING AGENT from time of production.|
|Packaging:||Available in 20 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.