£9.95 delivery on orders excluding certain products & postcodes *
Available in 15,000 colours from the Mapei ColorMap colour system.
Elastocolor Pittura Paint once dried, forms a very elastic film, impermeable to water, but permeable to vapour (microporous), and at the same time gives the treated structure a pleasant aesthetic appearance. Due to its elastic characteristics it is suitable for application to Resitex used on Park Homes, Elastocolor protects and waterproofs concrete structures and renders which have hair-line cracks present as it forms a bridge over them with a strong and continuous coat. Use to protect the surfaces of concrete and cement renders from aggressive agents present in the atmosphere. Mapei Elastocolor is available in a vast range of colours that can be obtained with the ColorMap colour system.
Elastocolor Paint is a single component acrylic resin-based paint in water dispersion, which forms a film on the surface due to the action of natural light. Once completely dry, Elastocolor Paint forms a flexible finishing coat which is impermeable to water and aggressive agents in the atmosphere (CO2 - SO2), while remaining permeable to vapour. Suitable for anti carbonation use.
Elastocolor Pittura Paint has excellent resistance to ageing, freezing weather conditions and de-icing salts, and the photochemical film which forms makes it very difficult for dirt to remain attached to the surface.
Mapei Elastocolor Paint meets the main requirements of EN 1504-9 ('Products and systems for protecting and repairing concrete structures: definitions, requirements, quality control and conformity assessment. General principles for the use and application of systems'),and the requirements of EN 1504-2 ('Protection systems for concrete surfaces') for class: products for protecting surfaces coatings (coating, C) - protection against the risk of penetration (1.3) (protection against ingress, PI) (ZA.1d) + control of humidity (2.2) (moisture control, MC), and increase in resistivity (8.2) (increasing resistivity, IR) (ZA.1e).
Preparation of the substrate
Surfaces to be protected with Elastocolor Paint must be perfectly clean and solid and must be treated beforehand with Mapei Malech or, if colours with low hiding power are used, with Mapei Quarzolite Base Coat. On surfaces where the type of curing cycle used is unsure, or if they are crumbly or have low absorbency, use Mapei Elastocolor Primer for the preliminary treatment cycle. The primed surface must never be shiny. Elastocolor Paint must only be applied on dry primer.
Before applying the primer coat, repair any areas of concrete which are in poor condition with controlled-shrinkage, fibre reinforced mortar from the Mapegrout or Planitop ranges of products. Completely remove all traces of dirt, dust, grease, oil, paintwork, saline efflorescence, mould and moss which could impede Elastocolor Paint from penetrating into the substrate. When choosing which cleaning cycle to use, on old surfaces it depends on the type of dirt, but cold water is usually sufficient. Cleaning the surface with hot water or steam is particularly recommended if oil or grease is present. Sand-blasting may also be used. If the surface is not dirty, the surface may simply be brushed down with a stiff brush and
blown with compressed air to remove the dust.
Elastocolor Paint may be applied on render and concrete with capillary cracks, even if they are widespread, without carrying out any special preparation operations. Check for larger cracks and, depending on the depth, provide suitable sealing and, if necessary, levelling with Mapei Elastocolor Rasante or Mapei Elastocolor Rasante SF reinforced with Mapei Elastocolor Net.
Preparation of the product
Dilute Elastocolor Paint with 10-15% of water and mix using a low-speed drill until it is completely blended. When preparing only partial quantities, we recommend mixing Elastocolor Paint as is in its original container before pouring off the quantity required.
Application of the product
Elastocolor Paint may be applied using traditional application techniques: by brush, roller or spray, on the dry coat of the specific primer. For effective and complete covering of the surface, during application with brush or roller, at least two coats are necessary. Under normal humidity and temperature conditions, wait 12-24 hours between each coat, and in all cases, only when the previous coat is completely dry. Examples of the final effect and finishes obtained using Elastocolor Paint are illustrated in the MAPEI colours in Design catalogue.
Maintenance after application
Elastocolor Paint may be washed with water and detergent (there are numerous products available on the market; carry out a preliminary test beforehand).
Components: | Single Pack |
Type: | Acrylic Resin in Water Dispersion |
Finish: | |
Stock Colours: | White |
Tintable: | Yes, to most RAL or British Standard codes. Please note, bespoke tints are non refundable / exchangeable |
VOC Content: | < 20 g/L |
Volume Solids: | 63% |
Suitable Substrates: | Concrete facades and structures |
Application Method: | Brush, Roller or Spray |
Theoretical Coverage: | 0.2 - 0.4 kg per m2 |
Wet Film Thickness (WFT): | |
Dry Film Thickness (DFT): | |
Induction Time: | - |
Pot Life: | - |
Surface Dry: | |
Overcoatable: | 12 - 24 hours at 20°C |
Fully Cured: | |
Cleaner / Thinner: | Water |
Shelf Life: | 2 years minimum in original unopened containers. |
Packaging: | Available in 20 Kg |