Fastrac Fast Drying Enamel is best used as a direct-to-metal decoration of ferrous metals. Alternatively it can be used as part of a finishing system for more demanding exposure scenarios. It is perfect for the protection and decoration of ferrous metals in many home projects such as fencing, gates and other ironmongery. Fastrac may also be used to paint previously painted or primed timber. In addition it is ideally suited as a refinish for agricultural, construction and earth moving equipment, having inherent high flexibility, moderate heat resistance and good resistance to mild chemicals, oils, hydrocarbons and sun light.
Application and use should always conform to the codes of practice described in BS 6150 and BS 5493
Brush and Roller – supplied ready for use. Use natural bristle brush, tapered and flagged, for best appearance. Thin, if required, with 0 - 5% white spirit.
Conventional Air Spraying - Thin with 10 - 20% white spirit as required, tip size – 1.5 mm, tip pressure 60psi (0.4MPa) approximately.
Airless Spraying - Thin with 0 - 15% white spirit as required, tip size - 18 thou (0.46mm) approximately, tip pressure - 2100 psi (15MPa) approximately.
Remove all rust scale, loose mill scale or other corrosion products by scraping and mechanical cleaning to SIS-St 3 (ISO 8501-1:1998). Bradite TD39 industrial strength detergent, washing and rinsing should be used with scrubbing to remove grease or oil. Intact areas of existing coatings should be roughened by abrasive manual or disc sanding, feathering back to a sound coating edge. Cracks and pits should be filled using a suitable metal filler before painting. Substrate should be dust free and completely dry before coating.
For unpainted softwood timber, knots should be sealed with a proprietary knotting compound and then primed with a proprietary quality wood primer. Unpainted hardwood & resinous timber substrates should be primed with a proprietary aluminium wood primer.
For industrial maintenance applications, high pressure steam cleaning to remove all loose, flaking paint and contamination back to a sound surface, is highly recommended.
|Type:||Silicone and polyurethane alkyd coating|
|Finish:||Gloss or Satin|
|Stock Colours:||Red, Yellow, Blue, Green, Black, White, Silver and Gold|
|Tintable:||Yes. Please note, bespoke tints are non refundable / exchangeable|
|VOC Content:||430 g/L|
|Suitable Substrates:||Degreased suitably prepared clean new and previously coated metal, wood and suitable primed non-ferrous metals.|
|Application Method:||Brush, Roller, Airless Spray or Conventional Air Spray|
|Theoretical Coverage:||13 m2/L/coat|
|Wet Film Thickness (WFT):||78 microns/coat|
|Dry Film Thickness (DFT):||35 microns/coat|
|Touch Dry:||2 hours at 20°C|
|Overcoatable:||After 16 hours minimum at 20°C|
|Fully Cured:||7 days at 20°C|
|Cleaner / Thinner:||White Spirit|
|Shelf Life:||12 months minimum in original unopened containers|
|Packaging:||Available in 1 and 2.5 Litres|
The manufacturers data sheets are available for download from this website. It is your responsibility to read and understand all aspects of the data sheets before you place an order and prior to application. Please pay special attention to the preparation, mixing and application temperatures of the product, cleaning of substrate and environmental factors such as temperature, rain etc. Quoted coverage rates are based on the manufacturers theoretical rates and may vary depending upon substrates absorption, texture and application. We always recommend a test is carried out to ensure suitability.
Customer further agrees that Promain have no liability for any errors or omissions contained within the Product Data Sheets and are not liable for failure due to misapplication or inadequate substrate cleaning and preparation. For more information please refer to our Terms & Conditions.
Mould and algae resistant with a high gloss finish it is fast drying even at low temperatures. Ideal for railings, lighting columns, st...